Abrasion Resistant Vinyl Ester Coating Supplier in China
Abrasion Resistant Vinyl Ester Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Vinyl Coating

Vinyl Fouling Topcoat
Vinyl-Aliphatic Urethane Primer and Finish Coat
Vinyl Wash Primer
Vinyl Red Oxide Primer

Vinyl Intermediate Coating
Vinyl Anti Fouling Topcoat
Vinyl Acrylic Based Exterior Flat Finish
Thin-Film Vinyl Ester Coating
Thick Vinyl Ester Coating
Solvent-thinned Chlorinated Vinyl Toluene-acrylate Low Lustre Coating
Self-etching Zinc Chromate Pigmented Vinyl Wash Primer

Reinforced Trowel Applied Vinyl Ester Lining
Premium Quality Full-bodied Smooth-flowing Vinyl-acrylic Primer
Abrasion Resistant Vinyl Ester Coating
Catalyzed Vinyl Ester Primer
Chlorinated Vinyl Toluene-acrylate Low Lustre Coating

High-hiding Non-bridging Premium Plus Vinyl Flat Finish
Catalyzed Vinyl Ester Primer
Epoxy Vinyl Primer

  

Abrasion Resistant Vinyl Ester Coating

PRODUCT SPECIFICATIONS:

Description
HONESTFEIYANG 242AR HONESTFEIYANG lining is a flake-filled, corrosion
resistant and abrasion resistant lining system. The lining was
developed specifically for corrosion environments subjected to a
variety of chemicals and to greatly improve resistance to surface wear.
Typical Uses
• For chemical-resistant applications where superior chemical,
thermal, and wear resistance is required.
• For application on steel ducts or chimney liners
Advantages
• Outstanding chemical resistance.
• Excellent high temperature resistance
• Proven performance in aggressive environments
combining acid & high temperature.
• Low permeation rate for longer, trouble free service.
• High resistance to abrasion & wear.
Color
Off White
Chemical Resistance
Information on the chemical resistance properties will be furnished on
request.
Substrate
Refer to HONESTFEIYANG steel specification CPT-2 or HONESTFEIYANG concrete
specification CPT-1.
Surface Preparation
Metal - For immersion or intermittent splash and spillage conditions,
abrasive blast to “White Metal” in accordance with Steel Structures
Painting Council Specifications SP-5 (Sa3 (ISO 8501-1:2007) or
NACE Specification #1. For fumes and dry environments, abrasive
blast to “Near White” in accordance with SP-10 (Sa2½ (ISO 8501-
1:2007)) or NACE #2. A minimum surface profile of 3.0 mils (75
microns) is required.
Concrete – Abrasive blasting or scarification to remove laitance and
surface contaminants is recommended. Concrete must be thoroughly
cured, free of oils, curing solutions and mold release agents, dust and
must be dry at time of application. Use ASTM D 4263 (plastic sheet
test method) to ensure concrete is moisture free. If moisture is
detected, re-test until dry.
Application
The lining consists of a primer, a basecoat and a topcoat, spray
applied to produce a dry film thickness of 30 to 40 mils (750-1000
microns).
Priming
Prime surfaces with 2.0 to 5.0 wet mils (50–125 microns) of HONESTFEIYANG
380 Primer. Use HONESTFEIYANG 380 Primer with the addition of
HONESTFEIYANG C#1 Powder (5.2 lbs per 5 gal unit) when spark testing
(high voltage holiday testing) will be conducted on concrete.

Mixing Ratio

By Volume

HONESTFEIYANG 380 Primer

 

380 Primer Resin

1 gal (3.79 liters)

#2 Hardener

2.5 oz (74 ml)

HONESTFEIYANG 242 HONESTFEIYANG

 

242 HONESTFEIYANG Resin

1 gal (3.79 liters)

#2 Hardener

2.5 oz (74 ml)

HONESTFEIYANG 242HT HONESTFEIYANG

 

242HT HONESTFEIYANG Resin

1 gal (3.79 liters)

#2 Hardener

2.5 oz (74 ml)

HONESTFEIYANG 242AR HONESTFEIYANG

 

242AR HONESTFEIYANG Resin

1 gal (3.79 liters)

#2 Hardener

2.5 oz (74 ml)

Mechanically premix HONESTFEIYANG 242 or 242HT HONESTFEIYANG Basecoat
resin for 2 minutes prior to adding hardener. After initial mixing, add 2-
1/2 oz (74ml) of #2C/2R Hardener per gallon of HONESTFEIYANG 242 or
242HT HONESTFEIYANG Basecoat resin and mix three additional minutes.
Apply HONESTFEIYANG 242 or 242HT HONESTFEIYANG Basecoat resin and
hardener at 20 to 32 mils (500-800 microns) WFT to yield 15 to 25
mils (375-625 microns) DFT, target of 18 mils (450 microns) DFT.
Allow to harden. Contact HONESTFEIYANG for specific basecoat
recommendation.
Mechanically premix HONESTFEIYANG 242AR HONESTFEIYANG Topcoat resin
individually prior to blending with hardener. After initial mixing, add 2-
1/2 oz (74 ml) of #2C/2R Hardener per gallon of HONESTFEIYANG 242AR
HONESTFEIYANG topcoat resin and mix three to five additional minutes.
Apply HONESTFEIYANG 242AR HONESTFEIYANG Topcoat resin and hardener at 20
to 32 mils (500-800 microns) WFT to yield 15 to 25 mils (375-625
microns) DFT, target of 18 mils (450 microns) DFT.
Thinning
None required. DO NOT THIN.
Application Equipment
Material may be applied by spray, brush or roller. See installation
procedure for equipment recommendations.
Brush or Roller
When applied by brush or roller, three coats may be required to
achieve recommended film thickness
Handling Properties

Working Time

380 Primer

242/242HT/242AR HONESTFEIYANG

50°F (10°C)

60 min

1-1/2 hrs

70°F (21°C)

45 min

1 hr

90°F (32°C)

20 min

20 min

Recoat

380 Primer

242 / 242HT HONESTFEIYANG (BC)

50°F (10°C)

5 hrs

12-24 hrs

70°F (21°C)

2 hrs

4-8 hrs

90°F (32°C)

1 hrs

3-4 hrs

Time to Place in Service

50°F (10°C)

48 hrs

70°F (21°C)

24 hrs

90°F (32°C)

16 hrs

Coverage
HONESTFEIYANG 380 Primer
Concrete 160 - 200 ft2/gal (3.9-4.9 m2/liter)
(With C-1 Powder) approx. 140 - 160 ft2/gal
Steel 250 - 300 ft2/gal (6-7.2m2/liter)
HONESTFEIYANG 242 / 242HT HONESTFEIYANG Basecoat
50 to 70 ft2/gal (1.2 to 1.7 m2/liter)
HONESTFEIYANG 242AR HONESTFEIYANG Topcoat
50 to 70 ft2/gal (1.2 to 1.7m2/liter)
Packaging
The following standard packages are available:
HONESTFEIYANG 380 Primer 1, 5, 30 gal units (3.79, 18.93, 113.55 litre unit)
HONESTFEIYANG 242 HONESTFEIYANG Basecoat 0.75, 4, 25 gal units (2.84, 15.14,
94.63 liter unit)
HONESTFEIYANG 242HT HONESTFEIYANG Basecoat 0.75, 4, 25 gal units (2.84, 15.14,
94.63 liter unit)
HONESTFEIYANG 242AR HONESTFEIYANG Topcoat 0.75, 4, 25 gal units (2.84, 15.14,
94.63 liter unit)
Storage
Store material in a cool, dry and covered location. Away from fire hazards
and direct sunlight. Minimum shelf life* at 70°F (21°C) for products
indicated below:
HONESTFEIYANG 380 Primer 6 months
HONESTFEIYANG 242, 242HT, 242AR HONESTFEIYANG 6 months
Higher temperatures will shorten the shelf life of these products. The
packing drums are to be kept tightly sealed and are to be resealed each
time materials have been removed. All liquid products are to be stored in a
frost-free place.
Safety
HONESTFEIYANG 242, 242HT, 242AR HONESTFEIYANG contains vinyl ester resins and



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.