Acrylic Copolymer Roof Coating Supplier in China
Acrylic Copolymer Roof Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Acrylic coating

Acrylic Multi-Purpose Primer
Acrylic Eggshell Floor Enamel
Acrylic Clear Coat
Acrylic Enamel For Interior Use

Acrylic Copolymer Exterior Flat Paint
Acrylic DTM Rust Resistant Coatings
Acrylic Elastomer Coating
Acrylic Copolymer Roof Coating
Waterborne Acrylic Enamel Undercoater
Acrylic High Infraed Heat Reflectivity Coating

Acrylic Finish Gloss
Acrylic Conversion Coating
Acrylic Metal Primer

Acrylic Patching Seam Sealer
Acrylic Conversion Coating
Two Pack Catalysed Acrylic Finish
Acrylic Elastomeric Wall Coating
Quick Drying Clear Urethane Alkyd Varnish
Aluminum Acrylic Coating Automotive Grade Acrylic Lacquer Topcoat
Baking Glossy Topcoat Based On Thermoset Acrylic Resin
Rapid Dry Pure Acrylic Coating
Acrylic Urethane Catalyzed Coating
Single Pack Acrylic Poly Siloxane Finish Coating

  

Acrylic Copolymer Roof Coating

PRODUCT SPECIFICATIONS:

DESCRIPTION: is an acrylic copolymer roof coating for asphalt and polyurethane foam roofing. It increases
light reflection, which helps reduce interior temperatures. This product may also be used on properly prepared and
primed wood, masonry and metal.
PRODUCT INFORMATION
SOLVENT TYPE RESIN TYPE
Waterborne Acrylic copolymer
FINISH
Flat. 1-2% on a 60° meter after.
COLOR
White
VISCOSITY AT 77°F (25°C)
80-85 Ku
MAXIMUM VOC CONTENT
85 g/L (as supplied)
SOLIDS BY VOLUME SOLIDS BY WEIGHT
36.0% 48.0%
WEIGHT P GALLON
10.30 lbs.
COMPOSITION BY WEIGHT
Pigment - 24.0% Vehicle - 76.0%
*Prime pigments ................... 14.0 Acrylic resins................................. 19.0
Reinforcing pigments............ 10.0 Alkyd resins..................................... 5.0
Water & additives.......................... 52.0
*Prime pigments include titanium dioxide (TiO2), plus all other pigments
directly adding to the hiding power of this paint.
RECOMMENDED FILM THICKNESS P COAT
Wet: 17.0 mils Dry: 6.0 mils
PRACTICAL COVAGE P COAT AT RECOMMENDED DRY FILM
THICKNESS
50-75 sq. ft. per gallon, depending on surface conditions.
AVAGE DRY TIME AT 77°F (25°C)
To touch: 1 hour
Recoat: 24 hours
APPLICATION EQUIPMENT
Brush, roller, airless spray
PACKAGING
Five-gallon containers
MATIAL SAFETY DATA SHEET
Form #1
SURFACE PREPARATION
Wash surface with water, using a hose with a pressure nozzle or a lowerpowered
high-pressure washer. Remove clinging dirt with a broom or brush.
Remove loose paint and deteriorated foam and patch where necessary.
Allow surface to thoroughly dry before application.
SPECIAL INSTRUCTIONS
·  CAUTION: Scraping or sanding surfaces of older buildings (especially
pre-1978) may release dust containing lead or asbestos. EXPOSURE TO
LEAD OR ASBESTOS CAN BE VY HAZARDOUS TO YOUR
HEALTH. Always wear appropriate personal protective equipment during
surface preparation, and finish cleanup of any residues by water-washing
all surfaces. For more information, see our brochure on


·  This product can neither cause nor prevent or cure the growth of mold,
mildew, or other forms of fungus. Excessive moisture and inadequate
ventilation are the main conditions that promote their growth. Correct any
such conditions before painting.
·  Apply HJ006 within 24 hours of foam application.
·  Apply 2 coats at a spread rate of no more than 90 sq. ft. per gallon. This
will give the proper dry-film thickness of 6.0 mils per coat, 12.0 mils total.
·  Do not apply HJ006 in areas where “ponding” occurs.
·  When applying over existing roof coatings, always test a small area for
compatibility before full application.
·  HJ006 is water-sensitive for 72 hours after application. Do not
apply if rain is anticipated during this period or if high humidity exists.
·  Do not apply when the air or surface temperature is below 50°F.
THINNING RECOMMENDATIONS
Do not thin.
CLEANUP
Warm, soapy water

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.