Acrylic Elastomeric Wall Coating Supplier in China
Acrylic Elastomeric Wall Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Acrylic coating

Acrylic Multi-Purpose Primer
Acrylic Eggshell Floor Enamel
Acrylic Clear Coat
Acrylic Enamel For Interior Use

Acrylic Copolymer Exterior Flat Paint
Acrylic DTM Rust Resistant Coatings
Acrylic Elastomer Coating
Acrylic Copolymer Roof Coating
Waterborne Acrylic Enamel Undercoater
Acrylic High Infraed Heat Reflectivity Coating

Acrylic Finish Gloss
Acrylic Conversion Coating
Acrylic Metal Primer

Acrylic Patching Seam Sealer
Acrylic Conversion Coating
Two Pack Catalysed Acrylic Finish
Acrylic Elastomeric Wall Coating
Quick Drying Clear Urethane Alkyd Varnish
Aluminum Acrylic Coating Automotive Grade Acrylic Lacquer Topcoat
Baking Glossy Topcoat Based On Thermoset Acrylic Resin
Rapid Dry Pure Acrylic Coating
Acrylic Urethane Catalyzed Coating
Single Pack Acrylic Poly Siloxane Finish Coating

  

Acrylic Elastomeric Wall Coating

PRODUCT SPECIFICATIONS:

DESCRIPTION: it is a premium acrylic elastomeric wall coating for exterior masonry. it
has exceptional flexibility and provides superior protection against wind-driven rain and moisture by bridging hairline
cracks and other small cracks that may develop in masonry surfaces. it accomodates normal expansion
and contraction by providing outstanding elastic recovery and resilience, even under conditions of extreme cold or heat.
it has outstanding resistance to ultraviolet light and dirt pick-up, and can be touched-up easily.
PRODUCT INFORMATION
SOLVENT TYPE RESIN TYPE
Waterborne 100% acrylic
FINISH (ASTM D 523)
Flat. 3-4% on a 60° gloss meter.
1-3% on an 85° gloss meter.
ELONGATION AT 77°F/25°C (ASTM D 2370)
300%
COLORS
Stock colors: White. Other colors must be special ordered.
VISCOSITY AT 77°F/25°C (ASTM D 562)
125-130 KU
MAXIMUM VOC CONTENT
40 g/L (as supplied)
SOLIDS BY VOLUME (ASTM D 2697) SOLIDS BY WEIGHT
50.0% ± 2% 65.0% ± 2%
WEIGHT P GALLON (ASTM D 1475)
11.50 lbs.
COMPOSITION BY WEIGHT
Pigment - 38.0% Vehicle - 62.0%
*Prime pigments ....................14.0 Acrylic elastomeric resins .............. 26.0
Reinforcing pigments .............24.0 Water & additives........................... 36.0
*Prime pigments include titanium dioxide (TiO2), plus all other pigments
directly adding to the hiding power of this paint.
RECOMMENDED FILM THICKNESS P COAT
Wet: 17.0 mils Dry: 8.0 mils
(See Special Instructions)
PRACTICAL COVAGE P COAT AT RECOMMENDED DRY FILM
THICKNESS
40-100 sq. ft. per gallon, depending on surface conditions and application
techniques.
AVAGE DRY TIME AT 77°F/25°C (ASTM D 1640)
To touch: 1-2 hours
Recoat: 24 hours
APPLICATION EQUIPMENT
Brush, roller, airless spray (See Special Instructions)
PACKAGING
Five-gallon containers. May be special ordered in 30-gallon and 55-gallon
drums.
:

MATIAL SAFETY DATA SHEET
Form #2
SURFACE PREPARATION
All surfaces must be cured, clean, dry, and free from dirt, dust, rust, stains,
grease, oil, mildew, wax, efflorescence and other contaminants. Remove all
loose, peeling, or chalky paint by sanding, scraping, wire brushing,
sandblasting, high-pressure washing or other appropriate methods.
hairline cracks with an elastomeric patching or caulking material. Structural
cracks and other cracks not caused by normal ground movement and settling
must be repaired before proceeding. Repaired surfaces should match the
surrounding surface texture. If efflorescence exists, remove all noticeable
deposits and prime the entire surface with HJ3537 -
Waterborne Epoxy Primer or Eff-Stop - Acrylic Masonry Sealer.
SPECIAL INSTRUCTIONS
• CAUTION: Scraping or sanding surfaces of older buildings (especially pre-
1978) may release dust containing lead or asbestos. EXPOSURE TO
LEAD OR ASBESTOS CAN BE VY HAZARDOUS TO YOUR HEALTH.
Always wear appropriate personal protective equipment during surface
preparation, and finish cleanup of any residues by water-washing all
surfaces. For more information, see our brochure on “Surface
Preparation Safety”


• This product can neither cause nor prevent or cure the growth of mold,
mildew, or other forms of fungus. Excessive moisture and inadequate
ventilation are the main conditions that promote their growth. Correct any
such conditions before painting.
• Airless spray application is recommended in order to achieve the optimum
film thickness. An airless spray unit with a minimum output of 2 gallons
per minute is recommended.
• Approved application of it must be ”pinhole free”, and have
a dry film thickness of 15- mils. Surface features mandate the method
of application and number of coats needed to achieve this.
• Do not apply when the air or surface temperature is below 50°F and do
not store in areas where temperatures are near freezing (37°F or below).
• Allow stucco and smooth-troweled plaster to cure at least 3 days before
sealing.
• Allow tilt-up concrete to cure at least 7 days before sealing with
HJ3537 .
THINNING RECOMMENDATIONS
Do not thin.
STORAGE
Store in a dry area. Protect from freezing. Extreme temperatures may cause
paint to become unusable. For example: Freezing and thawing may cause
paint to gel, and high heat may cause a solid skin to form.
CLEANUP
Warm, soapy water
DISPOSAL
For information on local options to dispose of unwanted, leftover paint, call
+86-755-26404303, or log onto www.polyurethane-paint.com.
SEALS
MASONRY
Plaster: HJ3537 or HJ3536
Stucco: HJ3537 or HJ3536
Tilt-up concrete: HJ3537 or HJ3536
Poured-in-place: HJ3537 or HJ3536
Brick: HJ3537 or HJ3536
Smooth trowel: HJ3537 or HJ 3321

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.