Acrylic Metal Primer Supplier in China
Acrylic Metal Primer paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Acrylic coating

Acrylic Multi-Purpose Primer
Acrylic Eggshell Floor Enamel
Acrylic Clear Coat
Acrylic Enamel For Interior Use

Acrylic Copolymer Exterior Flat Paint
Acrylic DTM Rust Resistant Coatings
Acrylic Elastomer Coating
Acrylic Copolymer Roof Coating
Waterborne Acrylic Enamel Undercoater
Acrylic High Infraed Heat Reflectivity Coating

Acrylic Finish Gloss
Acrylic Conversion Coating
Acrylic Metal Primer

Acrylic Patching Seam Sealer
Acrylic Conversion Coating
Two Pack Catalysed Acrylic Finish
Acrylic Elastomeric Wall Coating
Quick Drying Clear Urethane Alkyd Varnish
Aluminum Acrylic Coating Automotive Grade Acrylic Lacquer Topcoat
Baking Glossy Topcoat Based On Thermoset Acrylic Resin
Rapid Dry Pure Acrylic Coating
Acrylic Urethane Catalyzed Coating
Single Pack Acrylic Poly Siloxane Finish Coating

  

Acrylic Metal Primer

PRODUCT SPECIFICATIONS:

Type

 Sheen

Theoretical Spread Rate

Recommended Application

Thinner

Clean Up

Acrylic

Flat

350 -450 Sq. Ft. Per Gallon*

Brush, Roller or Spray

Water

Water

Dry Time:

Tack Free: 1 Hour

 Recoat: 2 – 4 Hours

Full Cure : 7 – 10 Days

PRODUCT NAME:

This is a water reducible Acrylic Metal Primer for coating steel, pre-engineered metal

36-11

building parts and other steel that is exposed to a normal commercial or residential

Acrylic Metal Primer

environment. It may be used in areas where solvent fumes are a problem or where

 

ecological concerns dictate. May be top coated with conventional alkyd, oil based and

 

latex type paints. It may also be used as a tie-coat over zinc rich primers. Provides

 

protection from rust bleed and flash rust. An excellent choice for galvanized metal.

WHE TO USE:

Ferrous Metal Galvanized Metal

On interior or exterior steel surfaces such as structural members, steel buildings, tools and machinery. This product is not intended for immersion services.

SURFACE PREPARATION:

The surface to be coated must be clean and free of dust, grease, oil, rust, mill scale and other surface contaminates that could interfere with adhesion. Grease and oil should be cleaned by using the thinner. Rust and mill scale must be removed by aggregate blasting, hand sanding vigorously or by conscientious power tool cleaning. Alternate surface preparation methods suitable for exposure and service may be substituted.

 

Stir thoroughly, making sure no pigment remains on the bottom of the can and the entire

APPLICATION:

contents are fluid and free of lumps. Acrylic Metal Primer may be applied by brush, roller

 

or spray at a rate of up to 450 square feet per gallon. Surface texture and application

 

method will affect actual yield. To thin product use clean water sparingly to achieve

 

desired consistency. Apply between 50º and 90º F only. IMPORTANT: This product is

 

compliant in markets as a Rust Preventive Coating.

*NOTE ON SPREAD RATE:

Actual spread rate will vary based upon numerous factors, including texture of the

 

substrate, application method, waste, surface porosity and thinning. The Theoretical

 

Spread Rate listed on this document has not taken into account these factors and is only

 

based upon the volume solids of this product and the recommended wet film thickness

 

when applied to a smooth substrate.

RESIN TYPE:

Acrylic

VOLUME SOLIDS:

Weight: Volume:

55.1 ± 1.0% 41.6 ± 1.0%

WEIGHT P GALLON:

10.8 lbs.

 

VISCOSITY:

90 – 95 KU

FLASH POINT:

0º F. or greater (TT-P-141, Method 4293)

SPECULAR GLOSS:

4 – 10 units @ 60º

SAG RATING:

Pass 8 mils

WET FILM THICKNESS:

3.6 to 4.6 mils

DRY FILM THICKNESS:

1.5 to 1.9 mils

CAUTIONS:

 

 

WARNING!

 

HARMFUL IF INHALED. HARMFUL IF SWALLOWED.

 

Causes eye, nose and throat irritation. May be harmful if absorbed through skin.

 

NOTICE: Reports have associated repeated and prolonged occupational overexposure to

 

solvent with permanent brain and nervous system damage. Intentional misuse by

 

deliberately concentrating and inhaling the contents may be harmful or fatal.

 

Use only with adequate ventilation. Do not breathe dust, vapors or spray mist. Ensure

 

fresh air entry during application and drying. If you experience eye watering, headache or

 

dizziness or if air monitoring demonstrates vapor/mist levels are above applicable limits,

 

wear an appropriate, properly fitted respirator during and after

 

application. Follow respirator manufacturer’s directions for respirator use. Do not get in

 

eyes, on skin or clothing. Wash thoroughly after handling.

 

First Aid: In case of contact, immediately flush eyes with plenty of water for at least 15

 

minutes. Get medical attention immediately. If you experience difficulty in breathing, leave

 

the area to obtain fresh air. If continued difficulty is experienced, get medical attention

 

immediately. If swallowed, do not induce vomiting. Get medical attention immediately.

 

If spilled, contain spilled material and remove with inert absorbent. Dispose of

 

contaminated absorbent, container and unused contents in accordance with local, state

 

and federal regulations.

 

Obtain and read the MSDS prior to using this product. KEEP OUT OF REACH OF CHILDREN

VOC/VOS STATEMENT:

This product contains a maximum of 240 grams VOC/VOS per liter of coating. (2.0 Pounds Per Gallon)

CATEGORY:

This product is compliant under the Transport Commission regulations as a Rust Preventive Coating.

:

CTIFICATION:

 

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.