Acrylic Urethane Catalyzed Coating Supplier in China
Acrylic Urethane Catalyzed Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Acrylic coating

Acrylic Multi-Purpose Primer
Acrylic Eggshell Floor Enamel
Acrylic Clear Coat
Acrylic Enamel For Interior Use

Acrylic Copolymer Exterior Flat Paint
Acrylic DTM Rust Resistant Coatings
Acrylic Elastomer Coating
Acrylic Copolymer Roof Coating
Waterborne Acrylic Enamel Undercoater
Acrylic High Infraed Heat Reflectivity Coating

Acrylic Finish Gloss
Acrylic Conversion Coating
Acrylic Metal Primer

Acrylic Patching Seam Sealer
Acrylic Conversion Coating
Two Pack Catalysed Acrylic Finish
Acrylic Elastomeric Wall Coating
Quick Drying Clear Urethane Alkyd Varnish
Aluminum Acrylic Coating Automotive Grade Acrylic Lacquer Topcoat
Baking Glossy Topcoat Based On Thermoset Acrylic Resin
Rapid Dry Pure Acrylic Coating
Acrylic Urethane Catalyzed Coating
Single Pack Acrylic Poly Siloxane Finish Coating

  

Acrylic Urethane Catalyzed Coating

PRODUCT SPECIFICATIONS:

PRODUCT DESCRIPTION
A high performance, two component coating for use where
appearance, durability, color and gloss retention plus chemical
and corrosion resistance are paramount. For use on automobiles,
trucks, trailers, railway cars, service stations, bulk tanks
or chemical (acid or caustic) trailers.
Itmeets 100 g/L maximum VOC compliant
coating requirements.
FEATURES
• Excellent color retention
• Solvent resistant
• Chemical resistant
• Excellent gloss retention
• Lead and Chromate free
• Ultra Low VOC
PRODUCT DATA
Description Results
Vehicle Type.............................. Acrylic Polyester Urethane
Colors Available in a variety of colors.
Gloss......................................... Full Gloss and Semi-Gloss
VOC (mixed)............................. 95 g/L (0.79 lbs/gal)
Weight/Gallon............................ 10.22 pounds
Solids by Weight (mixed)........... 64.1%
Solids by Volume (mixed).......... 53.3% (theoretical)
Viscosity.................................... 12-15" #3 ZAHN
Flash Point (white).................... 82oF
Dry Heat Resistance................. 300oF (149oC)
Freight Classification................. See MSDS
Packaging................................. 1 Gallon Mixed Units
APPLICATION DATA
Description Results
Application................................................. Spray, Brush or Roll
Mix Ratio................................................... 4:1 by Volume
Catalyst..................................................... HS-110 or HS-111
Recommended Thickness......................... 1.5 - 3.0 mils DFT
Dry Time @ 77oF, 50% RH
No Accelerator Brush/Roll
Recoat............................................... 6 hours
Tack Free.......................................... 8 hours
Handle............................................... 12 hours
With .5 fl oz/gal 99041
Recoat............................................... 4 hours
Tack Free.......................................... 7 hours
Handle............................................... 11 hours
Pot Life @75oF, 50% RH
No Accelerator
2X Viscosity....................................... 1.5 hours
Gel Time............................................ 4 hours
With .5 fl oz/gal 99041
2X Viscosity................................. 0.75 hours
Gel Time...................................... 2 hours
Coverage............................................. 566 sf/gal at 1.5 mils DFT
Thinner
Spray............................................... Exempt solvents i.e. t-Butyl
Acetate
Brush or Roll................................... Not Required
Clean Up............................................. HJ-092, MEK
The technical specifications for this data sheet are based on
product White.
CURED FILM PFORMANCE
Description Test Method Results
Q-UV A 340 ASTM D4587 > 90% gloss
(4,000 Hrs) retention (60o)
color change
DE < .5
Xenon Arc ASTM G147-96 > 95% gloss
(1,000 Hrs) quartz retention (60o)
borosilicate filters
Exterior Exposure ASTM D1014 > 90% gloss
45o South retension, 3
Dallas, Texas Years
24 Hour Chemical ASTM 1308 DI Water, 10%
Resistance H2SO4, 10%
Exposure NaOH, 25%
(No Effect) H3PO4, Xylene
& Mineral Spirits
Impact Resistance ASTM D2794 160 F & 160 R
EQUIPMENT RECOMMENDATIONS
Listed below are general equipment guidelines for the application
of this product. Job site conditions may require modifications
to these guidelines to achieve the desired results.
BRUSH: Use a solvent resistant bristle.
ROLL: Use a 1/4" nap solvent resistant core.
SPRAY APPLICATION (General): The following spray equipment
has been found suitable and is available from manufacturers

AIR ATOMIZED SPRAY:

 

Model

Air Cap

Fluid Tip

Fluid Delivery

Atomizing Pressure

Pressure

63 pb

66

oz/min

45 - 60 psi

Pressure

704

fx

oz/min

45 - 60 psi

AIRLESS SPRAY:


Model

Pump Ratio

Fluid Tip

Fluid Pressure

Filter Mesh

30:1

.011 - .013

1800 - 20

100

35:1

.011 - .013

1800 - 20

100

GENAL SURFACE PREPARATION
All surfaces must be sound, dry, clean and free of oil, dirt, grease,
wax, mildew, loose or flaking paint and other surface contaminants.
Remove loose, peeling, flaking or scaling paint and rust
by scraping, sanding or wire brush or blasting.
For best results, an SSPC-SP 5 white metal blast
is minimum for severe exposure. For moderately severe (nonimmersion)
exposures an SSPC-SP 6 ) commercial
blast can be used.
DIRECTIONS FOR USE
TINTING: May be tinted with HS tint colors only.
THINNING: This product has been formulated to be applied
without the need of additional thinning. However, application
with certain equipment and under various conditions may be
enhanced by reduction with the thinners specified. Please
note that additional reduction will increase VOC content of the
mixed coating.
PRIMS: Compatible primers are
Organic Zinc Rich Epoxy
APPLICATION: Mix thoroughly before use. Add 1 quart of
HS-110 or HS-111 per 1 gallon unit of HS4 then mix thoroughly
again. Only apply when air and surface temperature are between
40o – 100oF (7o - 38oC) and when the surface temperature
is at least 5oF or 3oC above the dew point.
DRYING TIME: Low temperature, high humidity, poor ventilation
and thick films will retard drying. HJ1104 may
be added at the rate of up to 0.5 fl oz per mixed gallon of HS4
to reduce the drying time.
CLEAN UP: Clean up paint tools or spills immediately with
recommended thinner, carefully observing cautions on paint
and thinner labels. Dried paint may be removed by scraping.
ALTNATE PRIMS: Contact Honest joy Company.
HEALTH AND SAFETY
Read the Material Safety Data Sheet (MSDS) and container
labels for detailed health and safety information. This product
is intended for industrial use by properly trained professional
applicators only.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.