Alkyd Baking Enamel Supplier in China
Alkyd Baking Enamel paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Alkyd coating

Urethane-Modified Alkyd Primer
Urethane Alkyd Enamel
Urethane Alkyd Based Toopcoat
Epoxy Ester Modified Alkyd Primer

Superior Quality Alkyd Glaze
Speedy-Dry Alkyd Enamel
Silicone Modified Alkyd Enamel
Semi-Transparent Organic Solvent Stain
Rust-Inhibitive Patented Acrylic Modified Alkyd Enamel
Quick-Drying Styrenated Alkyd Paint

Alkyd Urea Clear Coat
Transparent Modified Alkyd Sealer
Alkyd Semigloss Finish
Transparent Modified Alkyd Sealer
Quick Drying Modified Alkyd Based Primer
Rust Preventing Primer
Quick Drying Clear Urethane Alkyd Varnish
Versatile Finish Coat Based On Long Oil Alkyd Resin Exceptionally Durable Fast Drying Alkyd Paint
Fast Dry Alkyd Metal Primer
Alkyd Gloss Enamel
High Gloss Alkyd Aluminum Paint
Alkyd Baking Enamel

  

Alkyd Baking Enamel

PRODUCT SPECIFICATIONS:

Product Description
HJ-2411 is a baking glossy topcoat based on a modified alkyd
resin.
Recommended Use
For use on metal surfaces where a hard glossy and adherant
oily finish coat is required, specially in home appliances.
Outstanding Characteristics
- High gloss and colour retention
- Excellent sprayability
- High adhesion to different metallic surfaces
- Excellent flexibility
- Electrostaticly applicable
Surface Preparation
Remove oil and grease, etc. with suitable detergent. Remove
salt and other contaminants by (high pressure) fresh water
cleaning. Clean damaged area thoroughly by power tool
cleaning to ST3 (minor areas)
Or by abrasive blasting to minimum Sa2 , preferably to Sa2½
(for repair and maintenance) Abrasive blasting to
Sa 2½,SSPC-10 (for new steel)

Technical Data

 

Finish

Gloss, Semi gloss

Colour

 Upon request

Volume Solids

48 ± 2%

Specific Gravity

1. ± 0.1 gr/cm3 ( black: 1.0 )

Flash Point

26 °C

Recommended D.F.T.

25 - 40 microns

Theoretical coverage

16.8 - 10.5 sqm/lit 14.6 - 9.1 sqm/kg

Practical Coverage

Depends on loss factor

Flashing time

10 min

Stoving time

15- min at 160°C

Shelf life

12 months at 25°C

Package

liter container

Application Details

 

Application method

Air/Airless spray, Brush, Roller, deep

Nozzle orifice Nozzle pressure

.021" 150 bar / 20 Psi

Application temperature

10 - 50 °C

Mixing ratio

single pack

Thinner/Cleaner

RZT - 24

Pot life

N/A

Recoat interval

Wet on wet or after partially curing

Application Procedure HJ-2411
1. Flush all equipment with recommended cleaner before use.
2. Stir the product thoroughly with a power mixer.
3. For conventional spray, thin with no more than % of
recommended thinner for workability. For airless spray 10% of
thinner is normally sufficient.
4. Apply a wet coat by parallel passes. Overlap each pass 50% to
avoid bare areas, pinholes or holidays.
5. Double coat all welds, rough spots, sharp edges, rivets, bolts, etc.
to ensure proper thickness.
6. Check thickness of dry coating with a non-destructive dry film
thickness gauge. Recoat if greater thickness is required.
Note: If the maximum recoating interval is exceeded, roughening of
the surface is necessary to ensure intercoat adhesion.
7. Random pinholes, holidays and small damaged or bare areas can
be touched up by brush when the film is dry to touch. Larger areas
should be resprayed.
8-After coat applying and befor baking ,hold in 10-15 min to
evaporate solvents causing bubbling failure.
9. In confined areas ventilate with clean air during application and
drying until all solvents are removed.
10. Clean all equipment with recommended cleaner immediately
after use.
Limitations
Surface temperature must be at least 3°C above dew
point.
Relative humidity during application should be less than
80%.
Do not apply coatings under reverse environmental
conditions.
Safety
This product is flammable. Keep away from heat and open
flame. Keep container closed. Avoid prolonged and
repeated contact with skin.
Since improper use and handling can be hazardous to
health and cause fire or explosion, safety precautions
included with application instructions must be observed
during all storage, handling, use and drying periods.
If used in confined areas:
- circulate adequate fresh air continuously during
application and drying.
- Use fresh air masks and explosion proof equipment
- Prohibit all flames, sparks, welding and smoking
- Take precautionary measures against static discharges
Keep away from food products.
Storage and Handling
The products must be stored in accordance with national
regulations.
The products should be kept in a cool and well ventilated
place protected from heat and direct sunlight. Containers
must be kept tightly closed.
Handle with care. Stir well before use.
Remarks
The informations in this data sheet is given to the best of
our knowledge based on laboratory testing and practical
experience.
However we reserve the right to change the given data
without notice.
Any recommendation relating to the use of the products, is
based on data believed to be reliable. It is buyer to satisfy
itself of the suitability of the product for its own particular
use .
As the product is often used under conditions beyond our
control, we cannot guarantee anything but the quality of the
product itself.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.