Aluminum Acrylic Coating Supplier in China
Aluminum Acrylic Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Acrylic coating

Acrylic Multi-Purpose Primer
Acrylic Eggshell Floor Enamel
Acrylic Clear Coat
Acrylic Enamel For Interior Use

Acrylic Copolymer Exterior Flat Paint
Acrylic DTM Rust Resistant Coatings
Acrylic Elastomer Coating
Acrylic Copolymer Roof Coating
Waterborne Acrylic Enamel Undercoater
Acrylic High Infraed Heat Reflectivity Coating

Acrylic Finish Gloss
Acrylic Conversion Coating
Acrylic Metal Primer

Acrylic Patching Seam Sealer
Acrylic Conversion Coating
Two Pack Catalysed Acrylic Finish
Acrylic Elastomeric Wall Coating
Quick Drying Clear Urethane Alkyd Varnish
Aluminum Acrylic Coating Automotive Grade Acrylic Lacquer Topcoat
Baking Glossy Topcoat Based On Thermoset Acrylic Resin
Rapid Dry Pure Acrylic Coating
Acrylic Urethane Catalyzed Coating
Single Pack Acrylic Poly Siloxane Finish Coating

  

Aluminum Acrylic Coating

PRODUCT SPECIFICATIONS:

Description: Fast drying, thin film, economical
aluminum coating. Provides tight barrier protection to
properly prepared steel surfaces, as well as very
good heat deflection properties. Acrylic formulation
provides exceptional drying times. A good choice for
storage tanks & vessels located outside in direct
sunlight.
Features:
• High Gloss
• Good heat deflection
• Fast Drying
• Can be applied Direct-to-Metal
Solids Content: 23% By Volume
Theoretical Coverage:
• 368.92 mil ft²
• 184 ft²@ 2 mil
Allow for loss during mixing & application.
VOC Value:
• As 659 G/L
• Thinned 12 oz/gal with HJ105 – 678 G/L
SUBSTRATE & SURFACE PREPATION
Steel surfaces: Must be clean and dry. Prepared to a
minimum SSPC-SP1 Solvent cleaning to remove oil,
grease, dirt and other contaminants. Loose rust and
mill scale must be removed either by abrasive
blasting or hand/power tool cleaning. Maximum
performance will be achieved with a 1.0-2.0 mil blast
profile.
Galvanized Steel: Not recommended unless used
over a primer suitable for galvanized steel.
Previously painted surfaces: apply a test patch to
check compatibility with existing coating.
Primer: Alkyds, Epoxies, Zincs. Always first check
compatibility. A mist coat over Inorganic Zinc may be
needed to minimize bubbling.
APPLICATION EQUIPMENT
Spray Application:
Conventional
Airless.
Tip size .013
Output PSI- 00-2300
Brush & Roller: Recommended only for touch up
Brush: Natural Bristle
Roller: ¼” Nap cover with Phenolic Core
MIXING & THINNING
Mixing: Power mix to uniform color & consistency
Thinning:
Spray- Up to 12 oz/gal with HJ105
Brush & Roll- Up to 12oz/gal with HJ-52
APPLICATION:
Pre-application: Flush all equipment with thinner
HJ105
Temperature: Application range from 60F-100F
surface temperature. Do not apply below 50F.
Method: Apply one coat maintaining a wet edge to
achieve a DFT of 2-3 Mils. Multiple passes are
recommended to achieve proper DFT.
APPLICATION CONT.
Inspection: Visually inspect for voids in coating
film. A second coat in contrasting color is
recommended for adequate hiding.
Clean up & Disposal: After use, immediately flush
all equipment with thinner HJ105. Dispose of all
containers, solvents, and unused material in
accordance with local, state
regulations.
CURING SCHEDULE
Times based on 75F
Dry to touch: Min
Dry to recoat: Min
Final cure: 24 hrs
Dry times are widely affected by weather
conditions and film thicknesses.
PACKAGING & HANDLING
Unit sizes: One & Five Gal units
Shipping weight: 8.06 lbs/gal
Flash Point: 45° F

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.