Chlorinated Rubber Based Intermediate Coat Supplier in China
Chlorinated Rubber Based Intermediate Coat paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Vinyl Coating

Chemical Resistant Chlorinated Rubber Based Enamel
Chlorinated Rubber Based Anti-corrosive Primer
Chlorinated Rubber Swimming Pool Paint
Chlorinated Rubber Enamel

Chlorinated Rubber High Build Coating
Economical Anticorrosive Chlorinated Rubber Based Primer
Tintable Chlorinated Rubber Finish
Polychloroprene Rubber Solvent Based Primer
Phisically Drying Modified Chlorinated Rubber Based Primer
General Purpose Chlorinated Rubber Primer
Chlorinated Rubber Intermediate Coating

Chlorinated Rubber Micaceous Iron Oxide coating
Premium Quality Full-bodied Smooth-flowing Vinyl-acrylic Primer
Abrasion Resistant Vinyl Ester Coating
Catalyzed Vinyl Ester Primer
Chlorinated Rubber Based Intermediate Coat

Chlorinated Rubber MIO Intermediate Coating

  

Chlorinated Rubber Based Intermediate Coat

PRODUCT SPECIFICATIONS:

CHLOROKOTE HB MIO BROWN / GREY
A high build Chlorinated rubber based intermediate coat with lamellar micaceous iron oxide
pigment. The coating imparts tough and durable film with exceptional impermeability to moisture
and many industrial chemicals. The grey version contains Titanium dioxide apart from micaceous
iron oxide pigment.
PRODUCT INFORMATION SURFACE PREPARATION

Colour

Brown / Grey

STEEL SURFACES:

Finish

Matt

Surface should be perfectly clean and dry before applying appropriate primer.

Flash Point:

Above o C

Volume Solids:

43 % approximately

Recommended dry film thickness

50 -75 microns per coat.

Corresponding wet film thickness:

116 -174 microns

APPLICATION DETAILS

Method of application:
Airless spray / Brush / Roller
Airless spray recommended for uniform and high film build.
Notes on Airless Spray:
Tip Range: 21 -26 thou
Total out put fluid pressure-
2700 – 3000 psi
 (190 -246 kg/sq.cm)
Thinner: Specified thinner

TheoreticalSpreading Rate

8.6 – 5.7 Sq.metre per litre

Drying time

Touch dry-1 hours Hard dry-8 -12 hours

Interval before Overcoating

Minimum –16 hours Maximum –indefinite

LIMITATIONS

Coating not resistant to solvents, oils, grease and fats. The film is thermoplastic and is liable to soften and decompose above 65o C.

Storage life
 

Upto 12 months so
long as the material is stored in sealed
containers under
standard warehouse
storage conditions.

USES

Dry Heat
Resistance
 

Upto 65o C
(Intermittent)

Structural Steel, Pulp & Paper Mills, Chemical Plants, Bridges, Jetties, Pipelines, Tank Farms, Fertilizer Plants, Marine Installations, Sewage Plant

CHEMICAL RESISTANCE GUIDE (With suitable top coat)

EXPOSURE

SPLASH &
SPILLAGE

FUMES & OUTDOOR
EXPOSURE

Acids

Fair

Fair

Alkalis

Fair

Fair

Solvents

Poor

Poor

Salt

Very Good

Very Good

Water

Excellent

Excellent

NOTES
1. This cancels all previous literature on this product and is subject to revision without notice.
2. Do not apply when temperature falls below 10o C or rises above 50o C and when relative
humidity rises above 90%. Do not apply during rain, fog or mist.
3. Avoid over brushing of the product.
4. Use of thinners other than supplied or approved by Honestjoy may adversely affect product
performance and void product warranty whether express or implied.
HEALTH AND SAFETY
Please refer to the separate safety data sheet available with detailed information.
PRECAUTION
Provide adequate ventilation during painting.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.