Chlorinated Rubber High Build Coating Supplier in China
Chlorinated Rubber High Build Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Vinyl Coating

Chemical Resistant Chlorinated Rubber Based Enamel
Chlorinated Rubber Based Anti-corrosive Primer
Chlorinated Rubber Swimming Pool Paint
Chlorinated Rubber Enamel

Chlorinated Rubber High Build Coating
Economical Anticorrosive Chlorinated Rubber Based Primer
Tintable Chlorinated Rubber Finish
Polychloroprene Rubber Solvent Based Primer
Phisically Drying Modified Chlorinated Rubber Based Primer
General Purpose Chlorinated Rubber Primer
Chlorinated Rubber Intermediate Coating

Chlorinated Rubber Micaceous Iron Oxide coating
Premium Quality Full-bodied Smooth-flowing Vinyl-acrylic Primer
Abrasion Resistant Vinyl Ester Coating
Catalyzed Vinyl Ester Primer
Chlorinated Rubber Based Intermediate Coat

Chlorinated Rubber MIO Intermediate Coating

  

Chlorinated Rubber High Build Coating

PRODUCT SPECIFICATIONS:

Product Description
RZ-4141 is a high build phisically drying, modified
chlorinated rubber based topcoat.
Recommended Use
As a water resistant coating in underwater and above
water systems such as ships hulls, decks and
superstructures, offshores structures, structural steel and
pipping in chemical plants, refineries, bridges and cranes.
It is also suitable for drinking water systems.
Outstanding Characteristics
- Excellent water resistance
- Durability in severe marine atmosphere
- Applicable in high film thickness
Surface Preparation
The surface must be clean, dry and free of grease, millscale,
rust and dirt.

Technical Data
Finish Semi gloss
Colour Upon request
Volume Solids 42 ± 2%
Specific Gravity 1.25 ± 0.05 gr/cm3
Flash Point 24 °C
Recommended D.F.T. 50 - 80 microns
Theoretical coverage 8.4 - 5.2 sqm/lit
6.7 - 4.2 sqm/kg
Practical Coverage depends on loss factor
Touch dry 30 min. at °C
Hard dry 2 hours at °C
Thermal Resistance Continuous 60 °C
Non-continuous 65°C
Shelf life 12 months at 25 °C
Package liter container
Application Details
Application method Air / Airless spray,
Brush, Roller
Nozzle orifice .017" – .021"
Nozzle pressure 150 bar / 20 Psi
Application temperature 10 - 50 °C
Mixing ratio Single pack
Thinner/Cleaner HJ-53
Pot life N/A
Recoat interval Min 6 hrs at °C
Max none
(see remarks overleaf)
Application Procedure RZ-4141
1. Flush all equipment with recommended cleaner before use.
2. Stir the product thoroughly with a power mixer.
3. For conventional spray, thin with no more than -30%of
recommended thinner for workability. For airless spray 10% of
thinner is normally sufficient.
4. Apply a wet coat by parallel passes. Overlap each pass 50% to
avoid bare areas, pinholes or holidays.
5. Double coat all welds, rough spots, sharp edges, rivets, bolts, etc. to
ensure proper thickness.
6. Check thickness of dry coating with a non-destructive dry film
thickness gauge. Recoat if greater thickness is required.
Note: If the maximum recoating interval is exceeded, roughening of
the surface is necessary to ensure intercoat adhesion.
7. Random pinholes, holidays and small damaged or bare areas can be
touched up by brush when the film is dry to touch. Larger areas
should be resprayed.
8. In confined areas ventilate with clean air during application and
drying until all solvents are removed.
9. Clean all equipment with recommended cleaner immediately after
use.
Limitations
Surface temperature must be at least 3°C above dew
point.
Relative humidity during application should be less
than 80%.
Do not apply coatings under reverse environmental
conditions.

Safety
This product is flammable. Keep away from heat
and open flame. Keep container closed. Avoid
prolonged and repeated contact with skin.
Since improper use and handling can be hazardous
to health and cause fire or explosion, safety
precautions included with application instructions
must be observed during all storage, handling, use
and drying periods.
If used in confined areas:
- circulate adequate fresh air continuously during
application and drying.
- Use fresh air masks and explosion proof
equipment
- Prohibit all flames, sparks, welding and smoking
- Take precautionary measures against static
discharges
Keep away from food products.
Storage and Handling
The products must be stored in accordance with
national regulations.
The products should be kept in a cool and well
ventilated place protected from heat and direct
sunlight. Containers must be kept tightly closed.
Handle with care. Stir well before use.
Remarks
The information in this data sheet is given to the
best of our knowledge based on laboratory testing
and practical experience.
However we reserve the right to change the given
data without notice.
Any recommendation relating to the use of the
products, is based on data believed to be reliable. It
is buyer to satisfy itself of the suitability of the
product for its own particular use .
As the product is often used under conditions
beyond our control, we cannot guarantee anything
but the quality of the product itself.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.