Chlorinated Rubber Intermediate Coating Supplier in China
Chlorinated Rubber Intermediate Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us



Honest Joy Coating & Paint
Vinyl Coating

Chemical Resistant Chlorinated Rubber Based Enamel
Chlorinated Rubber Based Anti-corrosive Primer
Chlorinated Rubber Swimming Pool Paint
Chlorinated Rubber Enamel

Chlorinated Rubber High Build Coating
Economical Anticorrosive Chlorinated Rubber Based Primer
Tintable Chlorinated Rubber Finish
Polychloroprene Rubber Solvent Based Primer
Phisically Drying Modified Chlorinated Rubber Based Primer
General Purpose Chlorinated Rubber Primer
Chlorinated Rubber Intermediate Coating

Chlorinated Rubber Micaceous Iron Oxide coating
Premium Quality Full-bodied Smooth-flowing Vinyl-acrylic Primer
Abrasion Resistant Vinyl Ester Coating
Catalyzed Vinyl Ester Primer
Chlorinated Rubber Based Intermediate Coat

Chlorinated Rubber MIO Intermediate Coating


Chlorinated Rubber Intermediate Coating


Product Description
HONESTFEIYANG-9967 is a phisically drying, modified chlorinated
rubber based intermediate.
Recommended Use
As a water resistant intermediate in underwater and above
water systems such as ships hulls, decks and
superstructures, offshores structures, structural steel and
piping in chemical plants, refineries, bridges and cranes.
It is also suitable for drinking water systems.
Outstanding Characteristics
- Excellent water resistance
- Durability in severe marine atmosphere
- Good appearance
Surface Preparation
The surface must be clean, dry and free of grease, millscale,
rust and dirt.

Technical Data
Finish Flat, Semi gloss
Colour Upon request
Volume Solids 34 ± 2%
Specific Gravity 1.35 ± 0.05 gr/cm3
Flash Point 24 °C
Recommended D.F.T. 40 - 60 microns
Theoretical coverage 8.5-5.6 sqm/lit
6.3-4.2 sqm/kg
Practical Coverage depends on loss factor
Touch dry 30 min. at 20 °C
Hard dry 24 hours at 20 °C
Thermal Resistance Continuous 60 °C
Non-continuous 65 °C
Shelf life 12 months at 25 °C
Package 20 liter container
Application Details
Application method Air / Airless spray,
Brush, Roller
Nozzle orifice .017" – .021"
Nozzle pressure 150 bar / 2200 Psi
Application temperature 10 - 50 °C
Mixing ratio Single pack
Thinner/Cleaner HONESTFEIYANG-41
Pot life N/A
Recoat interval Min 6 hrs at 20 °C
Max none
(see remarks overleaf)

Application Procedure HONESTFEIYANG-9967
1. Flush all equipment with recommended cleaner before use.
2. Stir the product thoroughly with a power mixer.
3. For conventional spray, thin with no more than 20-30% of
recommended thinner for workability. For airless spray10% of
thinner is normally sufficient.
4. Apply a wet coat by parallel passes. Overlap each pass 50%
to avoid bare areas, pinholes or holidays.
5. Double coat all welds, rough spots, sharp edges, rivets, bolts,
etc. to ensure proper thickness.
6. Check thickness of dry coating with a non-destructive dry
film thickness gauge. Recoat if greater thickness is required.
Note: If the maximum recoating interval is exceeded,
roughening of the surface is necessary to ensure intercoat
7. Random pinholes, holidays and small damaged or bare areas
can be touched up by brush when the film is dry to touch.
Larger areas should be resprayed.
8. In confined areas ventilate with clean air during application
and drying until all solvents are removed.
9. Clean all equipment with recommended cleaner immediately
after use.
Surface temperature must be at least 3°C/ above
dew point.
Relative humidity during application should be less
than 80%.
Do not apply coatings under reverse environmental

This product is flammable. Keep away from heat
and open flame. Keep container closed. Avoid
prolonged and repeated contact with skin.
Since improper use and handling can be hazardous
to health and cause fire or explosion, safety
precautions included with application instructions
must be observed during all storage, handling, use
and drying periods.
If used in confined areas:
- circulate adequate fresh air continuously during
application and drying.
- Use fresh air masks and explosion proof
- Prohibit all flames, sparks, welding and smoking
- Take precautionary measures against static
Keep away from food products.
Storage and Handling
The products must be stored in accordance with
national regulations.
The products should be kept in a cool and well
ventilated place protected from heat and direct
sunlight. Containers must be kept tightly closed.
Handle with care. Stir well before use.
The information in this data sheet is given to the
best of our knowledge based on laboratory testing
and practical experience.
However we reserve the right to change the given
data without notice.
Any recommendation relating to the use of the
products, is based on data believed to be reliable. It
is buyer to satisfy itself of the suitability of the
product for its own particular use .
As the product is often used under conditions
beyond our control, we cannot guarantee anything
but the quality of the product itself.

As the product is often used under conditions
beyond our control, we cannot guarantee anything
but the quality of the product itself.


Contact Us
Honest Joy Coating & Paint. All rights reserved.