Chlorinated Vinyl Toluene-acrylate Low Lustre Coating Supplier in China
Chlorinated Vinyl Toluene-acrylate Low Lustre Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Vinyl Coating

Vinyl Fouling Topcoat
Vinyl-Aliphatic Urethane Primer and Finish Coat
Vinyl Wash Primer
Vinyl Red Oxide Primer

Vinyl Intermediate Coating
Vinyl Anti Fouling Topcoat
Vinyl Acrylic Based Exterior Flat Finish
Thin-Film Vinyl Ester Coating
Thick Vinyl Ester Coating
Solvent-thinned Chlorinated Vinyl Toluene-acrylate Low Lustre Coating
Self-etching Zinc Chromate Pigmented Vinyl Wash Primer

Reinforced Trowel Applied Vinyl Ester Lining
Premium Quality Full-bodied Smooth-flowing Vinyl-acrylic Primer
Abrasion Resistant Vinyl Ester Coating
Catalyzed Vinyl Ester Primer
Chlorinated Vinyl Toluene-acrylate Low Lustre Coating

High-hiding Non-bridging Premium Plus Vinyl Flat Finish
Catalyzed Vinyl Ester Primer
Epoxy Vinyl Primer

  

Chlorinated Vinyl Toluene-acrylate Low Lustre Coating

PRODUCT SPECIFICATIONS:

DESCRIPTION:
HJ SWIMMING POOL PAINT is a solvent-thinned chlorinated vinyl toluene-acrylate, low lustre coating
for use on unpainted or previously painted concrete swimming pools. HJ SWIMMING POOL PAINT
makes cleaning simpler and eases inspection for cleanliness and maintenance needs. HONEST will smooth or fill the
rough surfaces of concrete and reduce chances of abrasion and scratches to bathers. HONEST also protects concrete
surfaces that can slowly deteriorate from exposure to weather and water. Application may be by brush, roller or spray.
SURFACE PREPARATION:
The primary function of a swimming pool finish is to produce a water-tight coating with minimum permeability. Two
coats should be applied to provide adequate covering and maximum performance.
NEW CONCRETE POOLS:
• New concrete pools should be filled with water and allowed to age for 30-45 days.
• After the recommended aging period, empty the pool and wash it with a TSP (Trisodium Phosphate) solution or
other appropriate cleaner.
• Mix TSP with warm water, never use a soap-type detergent. Soap products can leave a soapy film on the surface
that will result in poor adhesion.
• Next, follow the HOW TO WASH YOUR POOL directions.
PREVIOUSLY PAINTED POOLS:
• Remove any paint that is peeling, blistering, powdering, chalking, or any paint that is not in good condition. Glossy
surfaces must be dulled. Sand blasting the old surface if preferred since it removes stubborn spots and leaves a
uniformly clean and porous surface. If only small areas require treatment, scraping and wire brushing should prove
adequate.
• Next, follow the HOW TO WASH YOUR POOL directions.
HOW TO WASH YOUR POOL
Cleaning:
• Mix eight ounces of TSP to each gallon of warm water. One gallon of this solution will wash approximately 0
square feet of wall or floor surface (29 square meters per 3.785 liters).
• Scrub surface with solution and heavy duty scrub brush. Always start on wall first and then proceed to the floor.
• Rinse off the residue with clean water right after you scrub. Be careful not to allow the pool washing solution to dry
on the surface.
• A power washer may be used (a minimum 2,000 psi required with a 15 degree tip maximum). When using a power
washer always follow manufacturer's recommendations and warnings.
Acid Etching:
• CAUTION--WHEN USING MURIATIC ACID ALWAYS READ AND FOLLOW THE MANUFACTUR'S
RECOMMENDATIONS AND USE THE PROP EQUIPMENT AND APPAREL.
• Acid etching is required on bare masonry surfaces like concrete or plaster. It is also effective for removing chalky
residue and hard mineral deposits on previously painted pools.
• Even on previously painted pools, we strongly recommend to acid etch the surface.
Mixing the Acid Solution:
• Allow the surface to dry before etching with a 10% solution of muriatic acid and water to properly prepare the
surface.
• Mix in a plastic bucket by slowly adding one gallon of % muriatic acid into one gallon of water. This will yield 2
gallons of 10% solution. One gallon of solution will be sufficient for etching 0 square feet of pool surface (19
square meters per 3.785 liters).
Etching Procedure:
• Liberally brush the acid solution on the surface. The acid will bubble on the surface when applied. As soon as the
bubbling ceases, thoroughly rinse the surface with clean water.
• Important--After etching, wash the pool surface a second time with TSP (see HOW TO WASH YOUR POOL
directions).
• Allow the pool surface to thoroughly dry after washing and etching before painting. Proceed to paint application.
APPLICATION:
• Once you have followed the correct surface preparation procedures for your swimming pool, you will be ready to
apply the finish coats of paint.
• The first coat of paint should be thinned, with up to one pint of mineral spirits per gallon of paint. Apply by brush or
roller (1/4-3/8 inch nap roller cover recommended). Allow to dry (see drying instruction).
• The first coat penetrates and fills surface voids to give the total film strong adhesion.
• Without thinning, apply the second coat of paint by brush, roller or spray gun. Allow a minimum of seven days after
application of the final coat of paint before filling the pool.
CLEAN UP:
Clean rollers and equipment with mineral spirits. Dispose of unused paint and waste in accordance with local, state
and federal regulations.
COVAGE:
One coat of paint will cover a range of 250-300 square feet per gallon (23-28 square meters per 3.785 liters),
depending on the surface.
DRYING:
Optimum drying conditions are 60°F-90°F (16°C-32°C) at 50% R.H. To Touch--3 hours. To Recoat--24 Hours. To Fill
Pool--7 Days. Lower temperatures and high humidity will slow dry time.
To spray, use the following recommendation or equal as a guide:
AIRLESS SPRAY
Tip . . . . . . . . . . . . . . . .013-.017”
Fan. . . . . . . . . . . . . . . . 40°-60° (8”-12”)
Pressure. . . . . . . . . . . . 1,500-2,000 PSI
HJ SWIMMING POOL PAINT
DESCRIPTION:
HJ SWIMMING POOL PAINT is a solvent-thinned chlorinated vinyl toluene-acrylate, low lustre coating
for use on unpainted or previously painted concrete swimming pools. HJ SWIMMING POOL PAINT
makes cleaning simpler and eases inspection for cleanliness and maintenance needs. HONEST will smooth the rough
surfaces of concrete and reduce chances of abrasion and scratches to bathers. HONEST also protects concrete
surfaces that can slowly deteriorate from exposure to weather and water. Application may be by brush, roller or spray.
Values based on HJ SWIMMING POOL PAINT WHITE, 5210
Weight Gallon: 10.17
Weight Solids: 57.50%
Volume Solids: 33.50%
Coverage:
@ 1 Dry Mil: 537 sq. ft./gallon
@ Spread Rate: 400 sq. ft./gallon (4.0 mils wet)
Deposits a 1.3 mil dry film
VOC (g/l): Not to exceed 600
Viscosity: 72-78 K.U. @ 77° F.
Gloss @ 60: 10 Max
Grind (Hegman): #2
DOT Class: Combustible, Flash Point 103°F.
Specification: TT-P-95 Performance Alternate
/NFPA: 1,2,0
Cure Time (Based on 70° F. & 50% R.H.):
To Touch: 3 Hours
To Recoat: 24 Hours
Recommended Thinner: Mineral spirits for clean-up and up to one pint per gallon for
first coat.
Temperature Resistance: Continuous 150° F., Intermittent 0° F.
CAUTION! Keep away from heat and open flame. Avoid prolonged contact with skin and breathing of vapor or spray
mist. Do not take internally. Close container after each use. Use only with adequate ventilation. KEEP OUT OF
REACH OF CHILDREN. For specific safety requirements, refer to the Material Safety Data Sheet.
LIMITATION OF LIABILITY: To the best of our knowledge, the technical data contained herein is true and accurate at
the date of issuance, but is subject to change without prior notice. We make no guarantee of any kind, express or
implied, including merchantability and fitness for particular purposes. Liability, if any, is limited to replacement of the
product or refund of the purchase price. Labor, or cost of labor, and other consequential damages are hereby
excluded.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.