HONEST is a tough thermosetting polyester powder coating with decorative and durability characteristics suitable for
interior and exterior product applications which exhibit excellent overall performance.
Tough, one coat finish Versatile
Interior/exterior applications Suitable for most environments
Film integrity Long intact life of coating
No solvents or emissions Less waste and pollution to the environment
HONEST 954 was developed primarily for use on aluminium, including window and door joinery, and extruded
aluminium panel work on residential and light commercial buildings.
Weather Good resistance to weathering.
Suitable for outdoor
Salt Spray 1000 hours on pre-treated
Heat Excellent resistance to 1°C
continuous service conditions.
Humidity Good resistance to 38°C/100%
humidity for 1000 hours on
Acid Resistant to spills of dilute acid.
Abrasion Good resistance to abrasion.
Alkali Resistant to spills of dilute Pencil Hardness Min H
alkali. Avoid contact. Hardness Average 15
Flexibility Excellent > 160 inch/lb Cross Hatch
Mortar Resistant White Spirits Resistant
Ethanol Resistant Xylene Slight softening/limit contact
Methyl Ethyl Ketone Softens/avoid contact Ethyl Acetate Softens/avoid contact
Colour A range of stock and made to
order solid colours
Specific gravity 1.3 - 1.7 @ colour
Gloss Level 25 - 98% at 60°, as required Shelf life 12 months when stored below
Application Method Electrostatic spray.
Clean Up Dust or vacuum loose powder. Avoid use of compressed air.
Cure Schedule Metal Temperature (°C) Time (minutes)
Cured Film Thickness Recommended: 80 μm
Range: 50 – 1 μm
Note: Light colours may require a higher minimum film build for optimum coverage and colour consistency.
Theoretical spreading rate at recommended film thickness
A coverage rate of 8 - 10m2/kg corresponds to 80μm cured film thickness assuming no loss. Practical spreading rates
will vary due to such factors as method and conditions of application and surface profile and texture.
Surfaces should be prepared according to appropriate standards .
All surfaces should be degreased and pre-treated for optimal performance. Suitable pre-treatment includes:
Aluminium Yellow chromate or green chromate/phosphate
Application Procedure and Equipment
1a) For fluidised bed, ensure uniform fluidisation of powder. Fluidised powder should resemble “simmering liquid”.
Aged or compacted powder may require pre-conditioning for several minutes to fluidise evenly.
1b) For box feeders, ensure probe is fully inserted in powder and operated as per manufacturer’s recommendations.
2. Apply by electrostatic spray.
3. Cure as per recommendations outlined above.
4. Test for cure of the coating by contact with a drop of solvent for
30 seconds. Surface should be wiped dry and immediately checked for softening. Only slight surface softening
Care and Maintenance
As a general rule, cleaning of externally located powder coating surfaces must take place every six months. Where
salts/pollutants are more prevalent such as seaside and industrial areas, a cleaning program should be carried out more
THREE STEPS TO CLEANING POWD COATED SURFACES
1. Remove loose deposits with a wet sponge (avoid scratching the surface by dry dusting).
2. Using a soft clean cloth and a mild detergent in warm water, clean the powder coating to remove dust, salt or other
3. Always rinse after cleaning with fresh water to remove any remaining detergent.
WARNING: In some cases, strong solvents recommended for thinning various types of paints and also for cleaning up
mastics/sealants are harmful to the extended life of the powder coated surface. These solvents should not be used for
cleaning purposes. If paint splashes or sealants/mastics need to be removed then the following solvents can be used
safely: Methylated Spirits, Turpentine, White Spirits, Ethyl Alcohol, Isopropanol.
Health and Safety
The MSDS is an integral part of using this product as it contains information on the potential health effect of exposure,
personal protective equipment needed and other relevant SH&E information.
Precautions and Limitations
• As a result of possible wide application variations and stoving conditions, some products and colours may show
variation between Powder Coating prepared samples and production applied material. Therefore,
it is the applicator and/or their customer’s responsibility to ensure the product conforms to their requirements.
• For optimum performance ensure recommended dry film thickness is obtained.
• Not recommended for use in highly corrosive environments such as severe marine or industrial locations.
• Not recommended for components which are exposed to constant temperatures exceeding 1°C.
Transport and Storage
Sizes: kg Flash Point: N/A
Weight: kg UN: N/A
Dangerous Goods Class: N/A Package Group: N/A