Eggshell Waterborne Interior Paint Supplier in China
Eggshell Waterborne Interior Paint paint coating manufacture Shenzhen China  
Home About Us Products Contact Us



Honest Joy Coating & Paint
Waterborne Coating

Waterborne Satin Enamel
Water-Borne Premium Quality Acrylic Primer
Water-Borne High Performance Interior Acrylic Primer Undercoat
Two-Part Water-Borne Linear Polyurethane Enamel

Water-Borne Epoxy Primer
Water Reducible Urethane Primer
Water Reducible Enamel
Water Miscible Epoxy Coating
Water Borne Inorganic Zinc Rich Silicate Primer
Two-Component Water-Borne Epoxy Primer

Water Based Two-Component Epoxy Polyamide Finish
Water-Borne High Performance Acrylic Metal Primer
Water Based Gloss Epoxy Enamel

Urethane Modified High Solids Water Borne Coating
Water-Borne High Performance Acrylic Metal Primer
Water Borne Acrylic Protective Coating
Arylic Thermo Plastic Waterbase Finish
Self-Levelling Epoxy Flooring Water Borne
Acrylic Water borne Paint Eggshell Waterborne Interior Paint
Environmentally Friendly Waterborne Metal Primer
Fast Drying Interior Exterior Primer
Acrylic Water borne Paint
High Gloss Waterborne Aliphatic Polyurethane Enamel


Eggshell Waterborne Interior Paint



General Properties

• Extreme hide, never more • Provides a mildew resistant
than two coats in any color coating
Color Technology, • Stains wash off easily
no color rub-off
• Good touch up • Self priming
• Easy application • Long lasting fresh look
• Easy clean up

Eggshell Finish is part of an innovative paint and colorant system integrating the best technologies to deliver superior durability for any color along with the promise of long lasting beauty. In addition to using 100% acrylic latex, proprietary resins have been incorporated to give the product its extraordinary performance properties.

Recommended For:
Residential or commercial applications where an eggshell finish with the highest performance characteristics are desired.
New or previously painted wallboard, plaster, masonry and wood; primed or previously painted metal; new or coated acoustic ceilings. It is ideal for surfaces where maximum durability is required and lasting color is desired. Allow paint to dry two weeks before washing


• Do not apply when air and surface temperatures are below
50° F (10° C)
• Only Waterborne Colorants can be added to

— Standard: No ready-mixed colors are available.

Technical Data◊ Pastel Base

Vehicle Type Acrylic & proprietary resins

  1. Tint Bases: 1X, 2X, 3X, & 4X

Tint Bases only with Waterborne Colorant.

Pigment Type Titanium Dioxide
Volume Solids 47.2%
Theoretical Coverage At 350-400 Sq. Ft. Recommended Film Thickness
Film Thickness — Wet 4.3mils — Dry 2.0 mils

— Special Colors: Contact your & Co. representative.

Dry Time @ 77° F — Dry To Touch 1 Hour
(25° C) @ 50% RH — To Handle 1 Hour

  1. To Recoat 1 Hour

Dries By Evaporation, Coalescence

-Class A (0-25) over non-combustible surfaces in accordance with ASTM E-84
-MPI 44
-VOC compliant in all regulated areas

47.0 g/L

Viscosity 109 ± 3 KU
Flash Point None
Gloss/Sheen Eggshell (12-22 @ 85°)
Surface Temperature at application – Min. 50° F
– Max 90° F

Thin With: See Chart

Clean Up Thinner Clean Water

Weight Per Gallon 12.2 lbs.

Storage Temperature – Min. 40° F – Max. 90° F

Volatile Organic Compounds (VOC)◊ 47.0 Grams/Liter
0.39 Lbs./Gallon


Surface Preparation
Surfaces to be painted must be clean, dry, and free of dirt, dust, grease, oil, soap, wax, scaling paint, water soluble materials and mildew. Remove any peeling or scaling paint, and sand these areas to feather edges smooth with adjacent surfaces. Glossy areas should be dulled. Drywall surfaces must be free of sanding dust. Spot prime with Eggshell Finish Paint
before and after filling nail holes, cracks, and other surface imperfections.
New plaster or masonry surfaces must be allowed to cure (30 days) before applying base coat. Cured plaster should be hard, have a slight sheen and maximum pH of 10; soft, porous or powdery plaster indicates improper cure. Never sand a plaster surface; knife off any protrusions and prime plaster before and after applying patching compound. Poured or pre-cast concrete with a very smooth surface should be etched or abraded to promote adhesion, after removing all form release agents and curing compounds. Remove any powder or loose particles.
Difficult Substrates: & Co. offers a variety of specialty primers for use over difficult substrates such as plaster, bleeding woods, grease stains, crayon markings, hard glossy surfaces, galvanized metal, or other substrates where paint adhesion or stain suppression is a particular problem. Your retailer can recommend the right problem-solving primer for your special needs.
WARNING! If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH approved respirator to control lead exposure. Clean up carefully with a vacuum and a wet mop. Carefully clean up with a vacuum and a wet mop.

Primer/Finish Systems
Eggshell paint is self priming on most surfaces. will act as
its own primer, providing the optimal foundation for the subsequent finish
coat. On bare substrates two coats are required; previously painted
surfaces can be finished with 1 or 2 coats.
Special Note: For certain deep colors, Color Foundation must be
used to achieve maximum hide and the desired topcoat color. Consult your
Wood, New:
Primer/Finish: 1 or 2 coats Eggshell paint.
Wood, Repaint:
Primer: Spot prime painted wood as needed with Eggshell paint.
Finish: 1 or 2 coats Eggshell paint.
Plaster/Wallboard, New:
Primer/Finish: 1 or 2 coats Eggshell paint.
Plaster/Wallboard, Repaint:
Primer: Spot prime as needed with Eggshell paint.
Finish: 1 or 2 coats Eggshell paint.
Masonry, New:
Rough or Pitted Masonry:
Primer: Latex Block Filler (160).
Finish: 1 or 2 coats Eggshell paint.
Smooth Poured or Precast Concrete:
Primer/Finish: 1 or 2 coats Eggshell paint.
Masonry, Repaint:
Primer: Spot prime painted masonry as needed with Eggshell paint.
Finish: 1 or 2 coats Eggshell paint.
Unpainted Metal (Ferrous):
Primer: Latex Low Lustre Metal & Wood Enamel
or Alkyd Low Lustre Metal & Wood Enamel .
Finish: 1 or 2 coats of Eggshell paint.

Mixing of Paint: Stir thoroughly before and during use.
Use the same brushing techniques as you would for any low-VOC
compliant interior coating. recommends an extra firm
nylon polyester brush for best results.
offers excellent flow and leveling. Do not over brush in the attempt
to smooth out brush marks.
We recommend the shed-resistant, 3/8" nap
roller cover for best results. dries faster than other acrylic paints, so
avoid lap marks by maintaining a wet edge. Roll out vertical sections in 3'
to 4' widths.
If your edge begins to dry or you see that you missed a spot and the paint
is already setting up, allow it to dry completely before touching up that area.
This product can also be sprayed; refer to the chart below for spray



Conditioning with Extender may be necessary under certain conditions to adjust open time or spray characteristics.The chart below is for general guidance
 Mild conditions
 Severe conditions
Humid (RH> 50%) with no direct sunlight & with little to no wind
Dry (RH<50%), in direct sunlight,
or windy conditions
Brush: Nylon / Polyester  
No thinning
Add 518 Extender or water:
 Max of about 1/2 pint or 8 fl. oz. to a gallon of paint
Never add other paints or solvents.
3/8’ Roller Cover
Spray: Airless
1000 -00 psi
Tip: 0.013-0.017


Cleanup: Wash painting tools in warm soapy water immediately after use. Spray equipment should be given a final rinse with mineral spirits to prevent rusting.
USE COMPLETELY OR DISPOSE OF PROPLY. Dry, empty containers may be recycled in a can recycling program. Local disposal requirements vary; consult your sanitation department or state-designated environmental agency on disposal options.
Environmental, Health & Safety Information
Use only with adequate ventilation. Do not breathe spray mist or sanding dust. Ensure fresh air entry during application and drying. Avoid contact with eyes and prolonged or repeated contact with skin. Avoid exposure to dust and spray mist by wearing a NIOSH approved respirator during application, sanding and clean up. Follow respirator manufacturer’s directions for respirator use. Close container after each use. Wash thoroughly after handling.
FIRST AID: In case of eye contact, flush immediately with plenty of water for at least 15 minutes; for skin, wash thoroughly with soap and water. If symptoms persist, seek medical attention. If you experience difficulty breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical attention immediately.
IN CASE OF SPILL – Absorb with inert material and dispose of as specified under Thinning/Cleanup.
Refer to Material Safety Data Sheet for additional health and safety information.




Contact Us
Honest Joy Coating & Paint. All rights reserved.