Environmentally Friendly Waterborne Metal Primer Supplier in China
Environmentally Friendly Waterborne Metal Primer paint coating manufacture Shenzhen China  
Home About Us Products Contact Us



Honest Joy Coating & Paint
Waterborne Coating

Waterborne Satin Enamel
Water-Borne Premium Quality Acrylic Primer
Water-Borne High Performance Interior Acrylic Primer Undercoat
Two-Part Water-Borne Linear Polyurethane Enamel

Water-Borne Epoxy Primer
Water Reducible Urethane Primer
Water Reducible Enamel
Water Miscible Epoxy Coating
Water Borne Inorganic Zinc Rich Silicate Primer
Two-Component Water-Borne Epoxy Primer

Water Based Two-Component Epoxy Polyamide Finish
Water-Borne High Performance Acrylic Metal Primer
Water Based Gloss Epoxy Enamel

Urethane Modified High Solids Water Borne Coating
Water-Borne High Performance Acrylic Metal Primer
Water Borne Acrylic Protective Coating
Arylic Thermo Plastic Waterbase Finish
Self-Levelling Epoxy Flooring Water Borne
Acrylic Water borne Paint Eggshell Waterborne Interior Paint
Environmentally Friendly Waterborne Metal Primer
Fast Drying Interior Exterior Primer
Acrylic Water borne Paint
High Gloss Waterborne Aliphatic Polyurethane Enamel


Environmentally Friendly Waterborne Metal Primer


Itis an environmentally friendly waterborne
metal primer with outstanding corrosion resistance.
This coating is based on a hydrophobic latex resin
system. Several types of corrosion inhibitors are
combined to work together to stop rust in this coating
Itis designed to be used with other waterborne
topcoats. Several solvent-based top coats can also be
coated over It(provided compatibility has been
Itis a fast-drying, thixotropic, low viscosity
coating that resists sagging. It also has excellent
resistance to settling in the can. This dry-to-touch film
offers extended protection in sheltered or unsheltered,
outdoor or indoor conditions. Excellent flexibility gives
optimal outdoor performance without cracking or
chipping due to prolonged exposure to sunlight.
• Carbon Steel
• Cast Iron
• Aluminum
• Stainless Steel
Check for settling in the can. If necessary, gently
agitate to a uniform consistency using a “squirrel
cage” type mixer, hand-held drill mixer, or other
equivalent method. Do not induce a vortex.
Conventional Spray:

Fluid hose should be 3/8” (0.95 cm) I.D. with a maximum length
of 50 feet (15.2 m). Pot should always have dual regulation and
be kept at the same elevation as the spray gun.

Hose should be 3/8” (0.95 cm) I.D. minimum, but a ¼” (0.6 cm)
I.D. whip end section may be used for ease of application. A
maximum length of 100 feet (30.5 m) is suggested. Best results
will be obtained using a 0.013”-0.017” (0.03 cm - 0.04 cm) tip at
10-1700 psi (83-117 bar).
NOTE: Nylon or Teflon type packings are available from pump
manufacturer and are highly recommended.
NOTE: Similar equipment may be suitable.
Recommended Thinner Fresh Water
Airless Spray None required
Appearance Gray viscous liquid
Non-volatile Content 46-51%
pH 8.5-9.5 (Neat)
Density 9.7-10.2 lb/gal (1.16-1.22 kg/l)
Solids by Volume 35-39%
Recommended DFT 1.5-3.0 mils (37.5-75 microns)
Theoretical Spread Rate 613 ft2/gal @ 1 mil
15 m2/l @ 25 microns
Dry to Touch Time* 30 minutes @ 75ºF (24ºC)
Temperature Stability 45º-90ºF (7º-32ºC)
Minimum Interval before Overcoating (Varies)
0.5-6.0 hours
Flash Point >248ºF (1ºC)
VOC (ASTM-3960) 1.2 lb/gal (143.8 g/l)
Viscosity 1600-20 cps
*Can be reduced with an increase in air flow
(on carbon steel 1010 Q-panels)
Dry Film Thickness
Mils (Microns) Hours to Failure
ASTM B-117 2.0 (50) 800-1100
(Salt spray)
ASTM D-1748 2.0 (50) 00+
ASTM G-85 A5 2.0 (50) 800-1100
Itis available in 5 gallon (19 liter) pails, 55 gallon
(8 liter) drums, liquid totes and bulk. Store in heated
warehouse to avoid freezing. Ithas a shelf life of
12 months.
Minimum storage temperature: 35ºF (2ºC)
Maximum storage temperature: 1ºF (49ºC)


Contact Us
Honest Joy Coating & Paint. All rights reserved.