Epoxy Ester Modified Alkyd Primer Supplier in China
Epoxy Ester Modified Alkyd Primer paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Alkyd coating

Urethane-Modified Alkyd Primer
Urethane Alkyd Enamel
Urethane Alkyd Based Toopcoat
Epoxy Ester Modified Alkyd Primer

Superior Quality Alkyd Glaze
Speedy-Dry Alkyd Enamel
Silicone Modified Alkyd Enamel
Semi-Transparent Organic Solvent Stain
Rust-Inhibitive Patented Acrylic Modified Alkyd Enamel
Quick-Drying Styrenated Alkyd Paint

Alkyd Urea Clear Coat
Transparent Modified Alkyd Sealer
Alkyd Semigloss Finish
Transparent Modified Alkyd Sealer
Quick Drying Modified Alkyd Based Primer
Rust Preventing Primer
Quick Drying Clear Urethane Alkyd Varnish
Versatile Finish Coat Based On Long Oil Alkyd Resin Exceptionally Durable Fast Drying Alkyd Paint
Fast Dry Alkyd Metal Primer
Alkyd Gloss Enamel
High Gloss Alkyd Aluminum Paint
Alkyd Baking Enamel

  

Epoxy Ester Modified Alkyd Primer

PRODUCT SPECIFICATIONS:

Description: It is a fast drying, thin
film, epoxy modified alkyd primer. Provides tight
barrier protection to properly prepared steel surfaces.
Provides increased chemical resistance compared to
conventional alkyds. It is specifically design for
use on electrical transformers, but may also be used
anywhere increased chemical resistance is desired.
Features:
• Fast Drying
• Increased chemical resistance
Solids Content: 49% By Volume
Theoretical Coverage:
• 785 mil ft²
• 262 ft²@ 3 mil
Allow for loss during mixing & application.
Recommended DFT: Two coats totaling 4-6 mils
VOC Value:
• As supplied 445 G/L
SUBSTRATE & SURFACE PREPATION
Steel surfaces: Must be clean and dry. Prepared to a
minimum SSPC-SP1 Solvent cleaning to remove oil,
grease, dirt and other contaminants. Loose rust and
mill scale must be removed either by abrasive
blasting or hand/power tool cleaning. Maximum
performance will be achieved with a 1.0-2.0 mil blast
profile.
Galvanized Steel: Not recommended unless used
over a primer suitable for galvanized steel.
Previously painted surfaces: Remove old coatings
by abrasive blasting.
APPLICATION EQUIPMENT
Spray Application:
Conventional
Airless.
Tip size .013-.015
Output PSI- 00-2300
Brush & Roller: Recommended only for touch up
Brush: Natural Bristle
Roller: ¼” Nap cover with Phenolic Core
MIXING & THINNING
Mixing: Power mix to uniform color & consistency
Thinning:
Spray- Up to 12 oz/gal with HJ105
Brush & Roll- Up to 12oz/gal with HJ-52
APPLICATION
Pre-application: Flush all equipment with thinner
HJ105
Temperature: Application range from 60F-100F
surface temperature. Do not apply below 50F.
Method: Apply one coat maintaining a wet edge to
achieve a WFT of 4-6 Mils. Multiple passes are
recommended to achieve proper WFT.
APPLICATION CONT.
Inspection: Visually inspect for voids in coating
film. A second coat in contrasting color is
recommended for adequate hiding.
Clean up & Disposal: After use, immediately flush
all equipment with thinner HJ105. Dispose of all
containers, solvents, and unused material in
accordance with local, state
regulations.
CURING SCHEDULE
Times based on 75°F
Dry to touch: 30 min
Dry to recoat: before 2 hours after 24
Dry to topcoat: before 2 hours after 24
Final cure: 24 hrs
Dry times are widely affected by weather
conditions and film thicknesses.
PACKAGING & HANDLING
Unit sizes: 1, 5, & 50 gallon containers
Shipping weight: 11.5 lbs/gal
Flash point: 81° F

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.