Exceptionally Durable Fast Drying Alkyd Paint Supplier in China
Exceptionally Durable Fast Drying Alkyd Paint paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Alkyd coating

Urethane-Modified Alkyd Primer
Urethane Alkyd Enamel
Urethane Alkyd Based Toopcoat
Epoxy Ester Modified Alkyd Primer

Superior Quality Alkyd Glaze
Speedy-Dry Alkyd Enamel
Silicone Modified Alkyd Enamel
Semi-Transparent Organic Solvent Stain
Rust-Inhibitive Patented Acrylic Modified Alkyd Enamel
Quick-Drying Styrenated Alkyd Paint

Alkyd Urea Clear Coat
Transparent Modified Alkyd Sealer
Alkyd Semigloss Finish
Transparent Modified Alkyd Sealer
Quick Drying Modified Alkyd Based Primer
Rust Preventing Primer
Quick Drying Clear Urethane Alkyd Varnish
Versatile Finish Coat Based On Long Oil Alkyd Resin Exceptionally Durable Fast Drying Alkyd Paint
Fast Dry Alkyd Metal Primer
Alkyd Gloss Enamel
High Gloss Alkyd Aluminum Paint
Alkyd Baking Enamel

  

Exceptionally Durable Fast Drying Alkyd Paint

PRODUCT SPECIFICATIONS:

DESCRIPTION: Alkyd Zone Marking Paint is an exceptionally durable, fast drying alkyd paint for striping and lane marking on asphalt or concrete, driveways, parking lots, sidewalks, curbs, or airport runways. This product has excellent hide and bleed resistance and dries to a gloss-free, highly visible finish.
SPECIAL CAUTIONS: On asphalt, a test patch should be made to check bleeding prior to painting. New asphalt surfaces occasionally must be allowed to cure and weather to prevent excessive bleeding through the dried paint.
To obtain satisfactory dry, apply only when relative humidity is below 85% and temperature is above 50°F. (10°C).
SURFACE PREPARATION: GENAL - Surface should be dry and free from oil, grease, dirt and other contaminants. Oil and grease can be removed from concrete with strong alkali cleaners or with solvent emulsion cleaners.
MIXING: Stir each container thoroughly before using. Apply at package viscosity.
APPLICATION: One coat at the recommended application rate will provide adequate durability and wear resistance.
To obtain satisfactory dry, apply only when humidity is below 85% and temperature is above 50°F. Best drying speeds require 65°F. or above.
Brush . . . . Flow on a full wet coat. Do not brush back into partially set up coating.
Marking Machines . . . Follow instructions for specific machine used.
Spray . . . . Use the following equipment recommendations as a guide:
AIRLESS SPRAY:
Tip . . . . . . . . . . . . . . . . . . .013-.015"
Fan . . . . . . . . . . . . . . . . . 25°-60°
Pressure . . . . . . . . . . . . 10-1600 PSI
CLEAN UP: Clean brushes and equipment with mineral spirits. Dispose of unused paint and waste in accordance with local, state and federal regulations.
COVAGE: Street Marking Paint will cover 150-250 square feet per gallon (14-23 square meters per 3.785 liters) or 600 to 700 lineal feet of four-inch wide line, depending on surface roughness. Approximate dry mil thickness of 4.6 to 2.8 mils at application rate of 150 to 250 square feet per gallon.
DRYING:
Optimum drying conditions are 60° F. to 90° F. (16° C. to 32° C.) at 50% R.H.
To Touch . . . . . . . . . . . . 5-10 Minutes
To Recoat . . . . . . . . . . . 30-60 Minutes
Lower temperatures and high humidity will slow dry.
DESCRIPTION:
Alkyd Zone Marking Paint is an exceptionally durable, fast drying alkyd paint for striping and lane marking on asphalt or concrete, driveways, parking lots, sidewalks, curbs, or airport runways. This product has excellent hide and bleed resistance and dries to a gloss-free, highly visible finish.
Values based on Alkyd Zone Marking Paint, Yellow
Weight Gallon: 11.62
Weight Solids: 71.5%
Volume Solids: 47.8%
Coverage:
@ 1 Dry Mil: 768 sq. ft./gallon
@ Spread Rate: 400 sq. ft./gallon (4.0 mils wet)
Deposits a 1.9 mil dry film
VOC (g/l): Not to exceed 450
Viscosity: 82-87 K.U. @ 77° F.
Gloss @ 60: 10 Max, Flat
Grind (Hegman): #4-4.5
DOT Class: Flammable, Flash Point 57°F.
Specification: N/A
/NFPA: 1,3,0
Cure Time (Based on 70° F. & 50% R.H.):
To Touch: 10 Minutes
To Recoat: 60 Minutes
Recommended Thinner: None. Apply at package viscosity. Mineral spirits for clean-up
Temperature Resistance: Continuous 150° F., Intermittent 0° F.
WARNING! FLAMMABLE! Keep away from heat and open flame. Avoid prolonged contact with skin and breathing of vapor or spray mist. Do not take internally. Close container after each use. Use only with adequate ventilation. KEEP OUT OF REACH OF CHILDREN. For specific safety requirements, refer to the Material Safety Data Sheet.
LIMITATION OF LIABILITY: To the best of our knowledge, the technical data contained herein is true and accurate at the date of issuance, but is subject to change without prior notice. We make no guarantee of any kind, express or implied, including merchantability and fitness for particular purposes. Liability, if any, is limited to replacement of the product or refund of the purchase price. Labor, or cost of labor, and other consequential damages are hereby excluded.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.