Fast Drying Industrial Finishing Enamel Supplier in China
Fast Drying Industrial Finishing Enamel Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Fast Dry Cure,Fast Set Coating

Fast Dry Metal Primer
Rapid Drying Primer
Rapid Drying Copolymer Enamel
Quick Drying One-pack Flexible Primer

Quick Drying Synthetic Primer
Quick Drying Acrylic Primer
Quick Drying Acrylic Lacquer
Polypropylene Air Drying Single Pack Primer
One-component Fast Drying High Build Anti-corrosive Primer
Fast Drying Concrete Floor Paint
Fast Drying Industrial Finishing Enamel
Fast Cure Abrasion Resistant Coating
Fast Dry Fabrication Primer
All Purpose Fast Set Mortar
Fast Curing Enamel




  

Fast Drying Industrial Finishing Enamel

Quick Dry Alkyd Enamel is a fast drying, industrial finishing
enamel intended for coating various metal parts. It is ideal for
industrial, OEM and metal fabrication. It offers versatility and
efficiency of application because of its quick drying
properties.
ADVANTAGES
• Very fast air drying
• High Gloss
• Full color line plus custom mix colors
• Good one coat protection
• No critical recoat time (See Product Limitations, item 4)
• Can be applied using conventional, airless, or electrostatic
spray equipment or by dipping
LIMITATIONS:
• To improve flow and leveling, small amounts of Xylene
, Aromatic Naphtha (Hi-Flash)
should be used.
• Multiple passes to obtain film build are recommended rather
than a single heavy pass. Excessive film build may cause
solvent popping because of the quick drying nature of
this product.
• Use of very slow evaporating solvents may increase the tack
free time and keep the coating softer for a longer time.
• Quick Dry Alkyd Enamel has no critical recoat time and can be
recoated at any time. However, field conditions may vary and
recoating should be tested on a small area.
• Intended primarily for interior use. Gloss and color retention
may be limited on exterior exposures.
RECOMMENDED USES
• Metal parts • Tools
• Farm Equipment • Hand Trucks
• Drums • Ventilators
• Trash Containers • Bins
• Machinery • Benches
• Hoists • Metal Furniture
SPECIFICATIONS
RECOMMENDED SYSTEMS
Aluminum: Prime with 1 ct. Water-Reducible Wash Primer
@ 0.7 - 1.3 mils dft. then 1 or 2 cts. Quick Dry
Alkyd Enamel (HJ-078 Series) @ 0.8 - 1.2 mils dft/ct.
Galvanized Steel: Prime with 1 ct. Water-Reducible Wash
Primer @ 0.7 - 1.3 mils dft. then 1 or 2 cts.
Quick Dry Alkyd Enamel (HJ-078 Series) @ 0.8 - 1.2 mils dft/ct.
Steel or Iron (interior use): 1or 2 cts. Quick Dry Alkyd Enamel
(HJ-078 Series) @ 0.8 -1.2 mils dft/ct.
Steel or Iron (Exterior Use): Prime with Industrial Primer
SURFACE PREPARATION
Substrate should be free of grease, oil, dirt, fingerprints, drawing
compounds, any other contamination, to ensure optimum
adhesion and coating performance properties.
New Galvanizing: Remove all oil, grease, dirt, oxide and
other foreign material by Solvent Cleaning per SSPC-SPI
(do not use hydrocarbon solvents). Primer required, See
Recommended Systems.
Iron & Steel: Minimum surface preparation is Hand Tool Clean
per SSPC-SP2. Remove all oil and grease from surface by
Solvent Cleaning per SSPC-SP1. For better performance, use
Commercial Blast Cleaning per SSPC-SP6, blast clean all surfaces
using a sharp, angular abrasive for optimum surface profile
(2 mils). Remove all weld spatter and round all sharp edges by
grinding to a minimum 1/4” radius. Prime any bare steel within
8 hours or before flash rusting occurs.
Aluminum: Remove all oil, grease, dirt, oxide and other foreign
material by Solvent Cleaning per SSPC-SP1 (do not use hydrocarbon
solvents). Primer required.
Testing: Due to the wide variety of substrates, surface preparation
methods, and application methods and environments, the
customer should test the complete system for adhesion and
compatibility prior to full-scale application.
APPLICATION
For a wetter spray or to improve flow and leveling, reduce with
small amounts of Aromatic Naphtha (Hi-Flash) or
Xylene .
Conventional Spray:
Reducer: Xylene or Aromatic Naphtha (Hi-Flash)

Reduction Rate: -25%
Airless Spray:
Pressure: 1800 psi
Tip: .013"-.017"
Reducer: Xylene or Aromatic Naphtha (Hi-Flash)

Reduction Rate: 15-%
Electrostatic Spray:
Reducer for polarity: MEK or MIBK
Reduction Rate: 5%-10% for wrap (depending on equipment)
Reducer for flow: Xylene or Aromatic Naphtha
(Hi-Flash)
Reduction Rate: As needed
Dip: (small parts only)
Reducer: Xylene or Aromatic Naphtha (Hi-Flash)

Reduction Rate: 15-%
APPLICATION cont.
CLEAN-UP
Use Xylene , Aromatic Naphtha (Hi-Flash)
or other aromatic solvents. Follow manufacturer’s
safety recommendations when using any solvent.
PFORMANCE TIPS
• To improve flow and leveling, small amounts of Aromatic
Naphtha (Hi-Flash) should be used.
• Multiple passes to obtain film build are recommended rather
than a single heavy pass. Excessive film build may cause
solvent popping because of the quick drying nature of this
product.
• Use of very slow evaporating solvents may increase the tack
free time and keep the coating softer for a longer time.
• Quick Dry Alkyd Enamel has no critical recoat time and can be
recoated at any time. However, field conditions may vary and
recoating should be tested on a small area.
• Intended primarily for interior use. Gloss and color retention
may be limited on exterior exposures.
CHARACTISTICS
GLOSS: Full 80+ units
VOLUME SOLIDS: 29 ± 1% (may vary by color)
VISCOSITY: 30-50 seconds
30-40 seconds #4 Ford Cup
SHELF LIFE: 36 months, unopened, at 77°F
RECOMMENDED FILM THICKNESS:
Mils Wet: 3.5 - 5.0
Mils Dry: 1.0 - 1.5
SPREADING RATE (NO APPLICATION LOSS): @ 1 mil dft:
465 - 310 sq. ft. / gal.
DRYING SCHEDULE (1.0 MILS DFT, 77°F, 50% RH):
To Touch: 5-10 minutes
To Handle: 10-15 minutes
Tack Free: 15- minutes
To Recoat: 30 minutes
Force Dry: 10 minutes at 180°F
FLASH POINT: 45°F PMCC
VOC: 4.95 lbs/gal (594 g/l)
CURE: 7-10 days @ 77°F @ 50% RH
CAUTIONS
Thoroughly review product label for safety and cautions prior to
using this product.
Note: The information, rating, and opinions stated here pertain
to the material currently offered and represent the results of tests
believed to be reliable. However, due to variations in customer
handling and methods of application which are not known or
under our control, wecannot make any
warranties as to the end result. Please direct any questions or
comments to 86-755-26404303.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.