Fast Drying Interior Exterior Primer Supplier in China
Fast Drying Interior Exterior Primer paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Waterborne Coating

Waterborne Satin Enamel
Water-Borne Premium Quality Acrylic Primer
Water-Borne High Performance Interior Acrylic Primer Undercoat
Two-Part Water-Borne Linear Polyurethane Enamel

Water-Borne Epoxy Primer
Water Reducible Urethane Primer
Water Reducible Enamel
Water Miscible Epoxy Coating
Water Borne Inorganic Zinc Rich Silicate Primer
Two-Component Water-Borne Epoxy Primer

Water Based Two-Component Epoxy Polyamide Finish
Water-Borne High Performance Acrylic Metal Primer
Water Based Gloss Epoxy Enamel

Urethane Modified High Solids Water Borne Coating
Water-Borne High Performance Acrylic Metal Primer
Water Borne Acrylic Protective Coating
Arylic Thermo Plastic Waterbase Finish
Self-Levelling Epoxy Flooring Water Borne
Acrylic Water borne Paint Eggshell Waterborne Interior Paint
Environmentally Friendly Waterborne Metal Primer
Fast Drying Interior Exterior Primer
Acrylic Water borne Paint
High Gloss Waterborne Aliphatic Polyurethane Enamel

  

Fast Drying Interior Exterior Primer

PRODUCT SPECIFICATIONS:

a fast drying interior/exterior primer intended for industrial use on bare metal surfaces. Suitable applications include metal fabrication, structural steel, industrial machinery, cabinets, racking and shelving.
HIGHLIGHTS:

  1. ��

Fast dry economical primer designed for interior and limited exterior applications
��
Can be field top coated with water reducible alkyd enamels or solvent based enamels
��
Contains no heavy metals
��
2.8 lb / gallon VOC compliant
��
Less than 1 lb of organic /gallon of solids
��
Tap Water reduction and clean-up
��
Low odor

TECHNICAL PROPTIES*:


PROPTY

METHOD

RESULT

Color

 

Gray QAHJ-8303-GRY; White QAHJ-8303-WHT; Red Oxide QAHJ-8303-ROX & Black QAHJ-8303-BLK

Gloss @ 60° Angle

ASTM D523

Flat

Pencil Hardness

ASTM D3363

B

Conical Mandrel – 1/8” Bend

ASTM D522

Pass

Adhesion – Test Method B

ASTM D3359

5B

Substrates

 

CRS, HRS

Topcoat (If Used)

 

SPECTRACRON 100, 110** AQUACRON 880

*Results obtained over iron phosphated CRS panel. Coating applied as specified.
**Solvent based topcoats should only be applied after a 7 day cure.
PHYSICAL PROPTIES:


PROPTY

VALUE

Weight per gallon

9.8 – 10.3 lbs / gallon

Solid % (Weight)

43 ± 3%

Solid % (Volume)

29 ± 2%

Viscosity

93 – 100 Krebs Units

Flash Point

110ºF (43ºC)

VOC (less water)

2.7 – 2.8 lbs / gallon

VOE

1.3 ± 0.1 lbs / gallon

Coverage

433 – 465 sq ft / gallon at 1 mil (no loss)

Shelf Life

1 year unopened

SURFACE PREPARATION:
The surface should be clean and free of all contamination. Chemical pretreatment will improve adhesion; the addition of a topcoat will improve overall product performance properties.
APPLICATION DATA:
Mixing Instructions: Mix thoroughly before and during use
Wet Film Thickness: 4.8 – 5.5 mils
Dry Film Thickness: 1.4 – 1.6 mils
Thinner: Water (up to 8% if needed)
Brush Application: High Quality Synthetic Bristle Brush – for touch up only
Roller Application: 3/8” Nap Solvent Resistant Core
Line Flush/Clean up: TFA880-70 Aquathin Refresher can be used to purge lines and equipment


SPRAY
APPLICATION

SPRAY EQUIPMENT

PRESSURE POT

FLUID PRESSURE (PSI)

ATOMIZING AIR (PSI)

TIP

Conventional

95 *

3/8” Fluid

8 - 10

55

66SS X 66SD

HVLP

JGHV-531*

3/8” Fluid

8 - 10

55 - 60

FF

Air Assisted Airless

Alpha A.A.*

NA

1000-1500

30-50

.011 - .013

Airless

Airless

NA

1800-2300

NA

.013 - .015

*Or Equivalent
CURE SCHEDULE:
Air Dry @ 77°F: Dry to touch: 15 minutes
Dry to handle: – 30 minutes
To Topcoat: After 30 minutes
Force Dry: Flash 10 min @ ambient: 10 - minutes at up to 160F
ADDITIONAL INFORMATION:

  1. ��

Not intended for application below 50癋
��
Excessive film thickness and high humidity conditions can retard dry times
��
Dry times can be improved with air movement
��
In-Service Temperature: 150°F (Note: film color may yellow or darken as 150°F is approached, however,

the Film integrity will be maintained.)

  1. ��

Product is not recommended for use over galvanized substrates
��
Protect from freezing

AQUACRON is a registered trademark of PPG Industries, Inc.
CONTACT 1-866-PPG TRUE


It is recommended that the customer should trial the product for adhesion and compatibility using all substrates, surface preparation techniques and application processes in the environment the product will be intended to be used in prior to actual product application.

The technical data presented in this bulletin is based upon information believed by PPG to be currently accurate. However, no guarantees of accuracy, comprehensiveness or performance are given or implied. Continuous improvements in coatings technology may cause future technical data to vary from what is in this bulletin.

 

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.