Fast Drying Low VOC Zinc Rich Epoxy Primer Supplier in China
Fast Drying Low VOC Zinc Rich Epoxy Primer Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Zinc primer.htm

Zinc-rich Ethyl Silicate Based Coating
Zinc Silicone Primer Heat Resistant to 500F
Zinc Rich Epoxy Primer
Zinc Rich Epoxy Cold Galvanising Coating

Zinc Phosphate Primer
Zinc Phosphate High Build Anticorrosive Primer-Finish
Zinc Ethyl Silicate Primer
Zinc Chromate metal Primer
Weldable Modified Zinc Ethyl Silicate Pre-fabrication Primer
Two-component Zinc Rich Epoxy Primer
Surface Tolerant Reinforced Inorganic Zinc Primer

Solvent-borne Self-curing Inorganic Zinc Silicate Primer
Reinforced Inorganic Zinc Primer
Chlorinated Rubber Zinc Rich Coating

Epoxy Zinc Phosphate Iron Oxide Primer
Epoxy Polyamide Anticorrosive High Performance Primer

Fast Drying Low VOC Zinc Rich Epoxy Primer

Inorganic Hybrid Zinc Rich Protective High Temperature Primer
Quick Dry High Performance Zinc Phosphate Primer
Free Low VOC Rreinforced Inorganic Zinc Primer
Solvent-borne Self-curing Inorganic Zinc Silicate Coating



  

PRODUCT SPECIFICATIONS:

PRODUCT DESCRIPTION
A two-component, 4:1 ratio, high solids, fast drying, low VOC
zinc rich epoxy primer for industrial maintenance. Offers
excellent resistance to corrosion and exceptional adhesion
to ferrous metal substrates.
FEATURES
• High solids, low VOC
• Excellent adhesion
• High build
• Fast drying
• Corrosion resistant
• Chromate free
PRODUCT DATA
Description Results
Vehicle Type...........................Epoxy Modified Amine
Color Gray
Gloss......................................< 5 on 60o meter
VOC (mixed)...........................326 g/l (2.72 lbs/gal)
Weight/Gallon (mixed)............21 pounds
Solids by Weight (mixed)........84.4%
Solids by Volume (mixed).......62%
Viscosity (mixed) 2,500 cps ( #4 @
rpm)
Flash Point.............................51oF
Dry Heat Resistance..............250oF
Freight Classification..............Paint Flammable
APPLICATION DATA
Description Results
Application..............................Convential or Airless Spray
Mix Ratio................................4:1 by Volume

Recommended Thickness......2.5 - 3.5 mils DFT
Dry Time @ 77o F, 50% RH
Tack Free............................1 hour
To Handle...........................4 hours
To Recoat...........................2 hour
Pot Life
2X Viscosity........................8 hours
Gel Time.............................16 hours
Coverage................................398 sf/gal at 2.5 mils DFT
Thinner...................................Specified Reducer
Medium Reducer

The above product and application data for this technical data
sheet are based on product Gray.
CURED FILM PFORMANCE
Description Test Method Results
Adhesion to Steel ASTM D4541 > 500 psi
Hardness ASTM D3363 2H
Impact Resistance ASTM D2794 40 lbs direct
Corrosion Resistance ASTM B117 few #6, no under-
2,500 Hours Salt Fog cutting
EQUIPMENT RECOMMENDATIONS
Listed below are general equipment guidelines for the application
of this product. Job site conditions may require
modifications to these guidelines to achieve the desired
results.
SPRAY APPLICATION (General):
AIR ATOMIZED SPRAY:

 

Model

Air Cap

Fluid Tip

Fluid Delivery

Atomizing Pressure

Pressure

63 pb

66

oz/min

45 - 60 psi

Pressure

704

fx

oz/min

45 - 60 psi

AIRLESS SPRAY:


Model

Pump Ratio

Fluid Tip

Fluid Pressure

Filter Mesh

30:1

.015 - .021

1800 - 20

100

35:1

.015 - .021

1800 - 20

100

GENAL SURFACE PREPARATION
For best results, an SSPC-SP 5 white metal
blast is minimum for severe exposure. For moderate exposure
(non-immersion), an SSPC-SP 6 )
commercial blast should be used.
DIRECTIONS FOR USE
TINTING: Do not tint.
THINNING: Thin with Specified Reducer;
10-15% if local VOC regulations allow. VOC compliance will not be exceeded with these levels of
thinner. Alternate reducer HJ-029may be used as universal
thinner. Reduce viscosity with approved thinner only.
Note: Always know local VOC restrictions for coatings
applications in your area before thinning this product.
Thinning recommendations meet VOC restrictions
for architectural coatings. This product and other referenced
products may not meet VOC restrictions for your application
and may not be available in your area. Carefully read and
observe warning thinner labels.
APPLICATION: Apply by spray only. APPLY
ONLY when air and surface temperatures are between
44 - 100°F and the surface temperature is at least 5oF
above the dew point. Use of agitator pot or pail is strongly
recommended.
DRYING TIME: Under normal conditions, dries to touch
in 1 hour and to recoat in 2 hours. Low temperature, high
humidity, poor ventilation and thick films will retard drying.
CLEAN UP: Clean up skin, clothing, paint tools or spills
immediately with recommended thinner, carefully observing
cautions on paint and thinner labels. Dried paint may be
removed by scraping.
HEALTH AND SAFETY
Read the Material Safety Data Sheet (MSDS) and container
labels for detailed health and safety information. This
product is intended for industrial use by properly trained
professional applicators only.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.