Fibered White Elastomeric Coating Supplier in China
Fibered White Elastomeric Coating Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 



Honest Joy Coating & Paint
Texture coating
Quality Coarse-textured Coating
Quality Fine-textured Coating
vvv Textured Finish
Medium Fine Textured coating
Polyurethane Textured Topcoat
Epoxy polyamide texture Coating
Marble Finish
Rubber Soft Touch coating textured coating
Fibered White Elastomeric Coating

  

Fibered White Elastomeric Coating

Product Description
Honest-8801 Fibered White Elastomeric Coating is formulated using an Acrylic Polymer base that provides outstanding adhesion and superior reflectivity. The bright white finish reduces surface temperatures thereby minimizing thermal expansion and contraction. Under-the-roof temperatures are also reduced, lowering energy costs. Formulated to resist cracking and peeling, Honest-8801 Elastomeric provides excellent waterproofing capabilities and long-term mildew resistance.
Basic Use
Honest-8801 White Elastomeric Finish Coat will provide a highly elastic, weatherproofing barrier over metal (including aged galvanized and pre-painted metals).
Limitations
Do not apply below 50°F (10°C) or when rain is forecast. Applications during periods of low temperature or high humidity will extend dry time. Allow 4 – 6 hours for coating to dry prior to being subjected to rain, heavy dew or temperatures below 50°F. KEEP FROM FREEZING
Technical Data
Vehicle Base……………….………….…100% Acrylic Resin
Weight per gallon (approx.)...……………………..…11.7 lbs.
Solids by weight (ASTM 1644) ……………..….……. 67.8%
Solids by volume…………………....……….…..….. 52 ± 2%
Recycled content………………….……………………..28.5% Viscosity ASTM D 562…………………..…….…..> 140 KU
Elongation/Tensile @ 73°F ASTM D 2370
Initial Elongation…………..…………………………187%
Initial tensile Strength ………………………..…....288psi 1000 Hrs. Accelerated Weathering
Elongation…………..…………………..…..……112%
No Cracking or Checking
Dry film thickness…………………………..…..…….8.3 mils
(@ 1 gal. /100 sq. ft./gal. less surface absorption)
Permeance ASTM D 1653 A………………..……18.4 perms
Dry Time Sets to touch…………………….………1 hour
Between Coats…………..…….24 hrs minimum
pH………………………..……………………..……8.5 ± 0.5
Specific gravity…………..…………….………….……..1.41
Flash Point ………………………………….……None
VOC ……………………………………………< 50 g/l
Reflectivity ……………………………………………..86%
Therm. Emit. ……………………………………………89%
Solvent………..……………………..…………...Water
Clean Up…………..….……….…Warm, soapy water

Surface Preparation
All surfaces must be power washed to remove all dirt, loose paint and rust, excessive chalk, and other foreign matter, which could prevent proper adhesion. All silicone-based products must be removed. IMPORTANT: Where ponding water conditions persist beyond 48 hours, roof drains or other corrective measures must be installed to eliminate water build-up prior to coating the roof.
For the following substrates refer to the applicable System Specifications for detailed application procedures.
Metal Roofs: Remove all loose rust and prime areas where existing rust was cleaned using Honest-100 Rust Inhibiting Primer. Replace loose and/or missing fasteners. Repair defective seams, small holes, flashings around roof curbs and skylights with HJ-0040 or Honest-110 Flashing Compound. Stacks and areas behind penetrations where water may stand must be modified to shed water.
NOTE: New metal roofs contain residual oils from the manufacturing process of the panels. Allow the roof to weather six months before coating. Otherwise, etch panels using a mild acid solution or use an industrial degreaser .
On metal roofs, Honest-400 Bonding Primer is required. See Honest-400 technical data sheet for details.
Single-Ply:
Hypalon - refer to system specification and Honest-400 Bonding Primer for detailed application procedures.
EPDM - refer to system specification, Honest-500 Wash Primer and Honest-400 Bonding Primer for detailed application procedures.
Built-Up: Power wash entire surface. Repair any blisters, open seams, splits, and flashings with Honest-110 Flashing Compound or HJ-0040.
Concrete: Powerwash the entire surface then prime complete area using Honest-130 Grey Elastomeric Base Coat. Repair cracks and any weakened section of concrete using Honest-110 Flashing Compound or HJ-0040.

Application
Apply with a soft brush (avoid excessive brushing), roller or airless spray. If using airless spray equipment, recommended air pressure of 2,000 at the tip. Tip size of .35 - .45 and hose size 3/4” to 1/2”. Elastomeric is to be applied in two coats, a light gray base coat with the white finish coat being applied 24 hours after the initial application. This product has excellent suspension and requires minimal stirring. If the roof is hot, spray a water mist to prevent the coating from drying too fast. May be applied over hand damp, not wet to the touch, surfaces. DO NOT THIN.
Coverage
Metal
Five (5) Year
Honest-8801 Fibered White ….………1.25 gal./100 sq.ft.
Ten (10) Year System
Honest-8801 Fibered White ……..…... 2.0 gal./100 sq.ft.
Fifteen (15) Year System
Honest-130 Gray ………………….. …... 1 gal./100 sq.ft.
Honest-8801 Fibered White …..……...…. 2 gal./100 sq.ft.

****Honest-400 Bonding Primer Is Required for Kynar metal roofs ****
Single Ply
Five (5) year System
Honest-400 Bonding Primer... 1.0 gal./100 sq.ft.
Honest-8801 Fibered White ……..…..…1.5 gal./100 sq.ft.
Ten (10) year System
Honest-400 Bonding Primer…1.5 gal./100 sq.ft.
Honest-8801 Fibered White …...…..…… 3 gal./100 sq.ft.

Five (5) year
Honest-400 Bonding Primer….. 1 gal./100 sq.ft.
Honest-8801 Fibered White ………......….2 gal./100 sq.ft.
Ten (10) year System
Honest-400 Bonding Primer…1.5 gal./100 sq.ft.
Honest-8801 Fibered White …...…..…… 3 gal./100 sq.ft.
Polyurethane Foam
Five (5) year
Honest-8801 Fibered White …....…..........2 gal./100 sq.ft.

Ten (10) year
Honest-130 Gray …………………..…….1 gal./100 sq.ft.
Honest-8801 Fibered White …....……......2 gal./100 sq.ft.
Concrete
Five (5) year
Honest-8801 Fibered White………..……. 2 gal./100 sq.ft.
Ten (10) year
Honest-130 Gray …………………………1 gal./100 sq.ft.
Honest-8801 Fibered White………..….. .. 2 gal./100 sq.ft.
Note: Coverage may vary depending on the actual condition of the surface. The coverage rates shown are intended as minimum application recommendations. Over corrugated and irregular metal surfaces, allow for additional surface area by multiplying total square feet by 1.15.
Maintenance
It is recommended that the coating installation be checked on a regular maintenance schedule. Small area touch ups can be made at any time following recommended application procedures.
Technical Services
Technical advice on use of material for specific application and end use requirements is available from the manufacturer. Material Safety Data Sheet (MSDS) should be consulted for further Information. This product is for industrial and professional use only.
Packaging
55 gallon drums (8.2 liters)
5 gallon pails (18.9 liters)
Warranty
This product is manufactured of good materials and by competent workmen. Seller’s and manufacturer’s only obligations shall be to replace such quantity of product proved to be defective. Neither seller nor manufacturer shall be liable for any injury, loss or damage, direct or consequential, arising from the use or the inability to use the product. Before using, user shall determine the suitability of the product for his/her intended use; and user assumes all risk and liability.



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.