Fire Retardant Coating Supplier in China
Fire Retardant Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Fire proof retardant heat resistance coating

VOC Compliant Air Drying Silicone Based Heat Resistant Coating
Two-Component State-OF-The-Art Silicone Coating
Fouling Release Tiecoat

Single Component High Heat Aluminum Coating
High Heat Resistant Black Coating
Silicone Based Heat Resistant Coating
Quick Drying Heat Resistant Aluminium Enamel
Aluminium Heat Resistant Pure Silicone
Air Drying Self-Priming Heat And Corrosion Coating

Compliant VOC High Build Modified Silicone Coating
Solventborne Silicone Coating
Heat Reflective Ceramic Coating

General Purpose Aqueous Based Fire Retardant Surface Coating
Solventborne Silicone Coating
Air Drying Self-Priming Heat And Corrosion Coating
One-Coat Aluminum Fire Resistance Coating
Coloured Heat Resistant Acrylic Silicone
Fire Retardant Coating

  

Fire Retardant Coating

PRODUCT SPECIFICATIONS:

DESCRIPTION
Intumescent coating Fire Retardant (W) is based on specialty resins and chemicals that provide 1 to 2 hours fire protection by suppressing fire on various substrates, concrete plaster, acoustical tiles, wood and load bearing structural steel beams & columns. The coating has interior & exterior durability, provided there are no hot surfaces in the vicinity of 10 meters radius, boilers/high temperature ovens.
RECOMMENDED USES
For use over prepared steel, iron, aluminum, galvanized metal, plywood, fiberboard and natural wood substrate such as (1) Softwood – Pine, Cedar, Redwood (2) Hardwood - Oak, Maple, Birch, Walnut, Mahogany, and Gum.
CHARACTISTICS
Color:
Off White to Grey
Finish:
Flat
Volume Solid:
46% + 2%
Specific Gravity:
1.2 KGs / ltr
Recommended DFT:
500 – 650 Microns for 60 – 90 Minutes Protection
650 – 750 Microns for 2 Hours plus Protection
Spreading Rate@DFT:
0.92 – 0.7 m2 / ltr or
3.48 – 2.6 m2 / gallon @ 500 - 650 Microns DFT
Flash Point:
94 oC
Drying Schedule:
@ 25 oC/R.H.50
Dry to Touch:
1 Hour
To Handle:
4 Hours
To Recoat:
12 Hours
Shelf Life:
18 months, unopened at 25 oC
Reducer/Clean Up:
Water
APPLICATION PROCEDURES
Surface Preparation:Surface must be dry, clean and in sound condition. Remove oil, dust, dirt, millscale or other foreign substance to ensure good adhesion. Minimum surface preparation methods to be followed for (1) Iron and Steel – SSPC-SP2 or SP3 (2) Aluminum and Galvanizing – SSPC-SP1. Allow weathering of new galvanized steel for six months prior to coating. (3) Concrete should be cured, dry and clean. (4) Wood - Sand the surface with suitable grit sand paper and remove all the dust with a tack cloth or blast of clean air. If any dirt or grease remains prior to finishing it must be removed by solvent wiping.
Application Methods:
Conventional Spray:
Reduce 10% with water
Airless Spray:
Reduce 10% with water
Brush/Roller:
Reduction not recommended
SYSTEM RECOMMENDATION
Iron and Steel:
Latex Metal Primer
1 Coat
30 Microns DFT
Intumescent Coating
2 Coats
As Recommended
Acrylic Enamel
2 Coats
25 Microns DFT
per coat
Aluminum and Galvanized Metal:
Latex Metal Primer
1 Coat
30 Microns DFT
Intumescent Coating
2 Coats
As Recommended
Flat Tone Latex Finish
2 Coats
25 Micron DFT
per coat
Natural Wood/Fiberboard/Plywood:
Acrylic Primer Sealer
1 Coat
25 Microns DFT
Intumescent Coating
2 – 3 Coats
As Recommended
Acrylic Enamel
2 Coats
30 Microns DFT
per coat
* For a specific fire retarding system please feel free to contact Honestjoy .

***For further information on surface preparation methods and application procedures please refer to Honestjoy Surface Preparation bulletin.
SPECIAL TIPS
Excessive reduction of material can affect the film build, appearance, and adhesion. Any further specific technical information can be obtained from www.polyurethane-paint.com
SAFETY PRECAUTIONS
Spray under well-ventilated conditions. Do not breathe or inhale mist. When spraying, wear air mask. Avoid skin contact. Spillage on skin should immediately be removed with suitable cleanser, soap and water. Eyes should be flushed with water and medical attention sought immediately.

 

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.