Flake Filled Polyester Coating Supplier in China
Flake Filled Polyester Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Polyester Coating

TGIC Free Polyester Powder Coating
Reinforced Trowel Applied Polyester Lining Topping
Polyester Thick Film Coating
Polyester Flake Coating

Polyester Resin Fast Setting Bedding Mortar
Polyester Baking Enamel
High Quality Acrylic Polyester Resin Basecoat
Free Glass Flake Reinforced Polyester Coating
Flowable Rapid Setting Polyester Resin Mortar
Flake Filled Polyester Coating
Durable Polyester Powder Coating

Clear Polyester Powder Coating
Abrasion Resistant Glass Flake Reinforced Polyester Coating
Abrasion Resistant Glass Flake Reinforced Polyester Coating




  

PRODUCT SPECIFICATIONS:

Description
HONEST 252 FLAKELINE coating is a flake glass filled,
catalyzed polyester system which exhibits excellent
resistance to acids, salts, alkalis and many organic
solvents.
Typical Uses
• Metal processing areas
• Oil production facilities
• Chemical processing plants
• Waste treatment systems
Advantages
• Can be applied over concrete or steel
• Excellent resistance to acids
• Flake filled, providing better permeation resistance
• Meets FDA Requirements
Color
Off white and gray Consult HONEST for special colors
Chemical Resistance
Information on the chemical resistance properties will be
furnished on request.

Surface Preparation
Metal - For immersion or intermittent splash and spillage
conditions, abrasive blast to “White Metal” in accordance
with Steel Structures Painting Council Specifications SP-5
or Sa3 ) NACE Specification #1. For
fumes and dry environments abrasive blast substrate to
“Near White”, in accordance with SP-10 (Sa2½ (ISO 8501-
1:07)) or NACE #2. A minimum surface profile of 3.0
mils (75 microns) is required.
Concrete – Abrasive blasting or scarification to remove
laitance and surface contaminants is recommended.
Concrete must be thoroughly cured, free of oils, curing
solutions and mold release agents, dust and must be dry at
time of application. Use ASTM D 4263 (plastic sheet test
method) to ensure concrete is moisture free. If moisture is
detected, re-test until dry.
Application
The coating system consists of a primer, a base coat and a
topcoat, with a nominal dry film thickness of 30 to 40 mils
(750-1000 mircons).

Mixing Ratio

By Volume

HONEST HJ-A005

 

HJ-A005 Resin

1 gal (3.79 liters)

#2 Hardener

2.5 oz (74 ml)

HONEST 252

 

252 Resin

1 gal (3.79 liters)

#3 Hardener

2 oz (60 ml)

Priming
Prime surfaces with 2.0 to 5.0 wet mils (50-125 microns) of
HONEST HJ-A005 . Use HONEST HJ-A005 with the
addition of HONEST Powder (5.2 lbs per 5 gal unit /
2.4kgs per 18.93 liter unit) when spark testing (high voltage
holiday testing) will be conducted on concrete.
Mechanically premix HONEST 252 resin (i.e. Part A) 2
minutes individually prior to adding hardener. After initial
mixing, add 2oz (60ml) of #3C Hardener per 1 gallon (3.79 ltr)
of HONEST 252 resin and mix three additional minutes.
Apply HONEST 252 resin and hardener at to 32 mils
(500-800 microns) WFT to yield 15 to 25 mils DFT (375-625
microns), target of 18 mils DFT (450 microns). Allow to
harden. Repeat for second coat application.
Thinning
None required. DO NOT THIN.
Application Equipment
Material may be applied by spray, brush or roller. See
installation procedure for equipment recommendations.
Brush or Roller
When applied by brush or roller, three coats may be required
to achieve recommended film thickness.
Handling Properties

Working Time

HJ-A005

252

50°F (10°C)

approx. 60 min

approx. 100 min

70°F (21°C)

approx. 45 min

approx. 1 hr

90°F (32°C)

approx. min

approx. 45 min

 

Recoat

HJ-A005

252

50°F (10°C) 70°F (21°C)

approx. 5 hrs approx. 2 hrs

12-24 hrs 4-8 hrs

90°F (32°C)

approx. 1 hrs

3-4 hrs

 

Time to Place in Service

50°F (10°C)

48 hrs

70°F (21°C)

24 hrs

90°F (32°C)

16 hrs

Coverage
HONEST HJ-A005
concrete approx. 160 - 0 ft2/gal (3.9-4.9 m2/liter)
approx. 140 - 160 ft2/gal
(3.4-3.9 m2/liter)
steel approx. 250 - 300 ft2/gal (6-7.2m2/liter)
HONEST 252
25 to 35 ft2/gal (.6 to .85 m2/liter)

Storage
Store material in a cool, dry and covered location, away from fire
hazards and direct sunlight. Minimum shelf life* at 70°F (21°C) for
products indicated below:
HONEST HJ-A005 6 months
HONEST 252 6 months
Higher temperatures will shorten the shelf life of these products.
The packing drums are to be kept tightly sealed and are to be
resealed each time materials have been removed. All liquid
products are to be stored in a frost-free place.
Safety
HONEST 252 contains polyester resins and MEK
peroxide catalyst. The product’s components have been
formulated to optimize physical characteristics such as filling
capacity, abrasion, moisture and chemical resistance while
minimizing hazardous physical and health factors encountered
during application. A concerted effort is made to be aware of the
latest chemical toxicological information and to apply this
knowledge in a responsible manner to insure product safety.
During application of HONEST 252 materials, always
wear gloves and appropriate work clothing to minimize contact.
Ventilation is required with special consideration for enclosed or
confined areas. Air movement must be designed to insure
turnover at all locations in work area and adjacent areas to avoid
buildup of heavy vapors. Use caution when handling flammable
liquid, eliminate sources of ignition from work area and containers
with residues.
Observe safe storage practices by separating resins from
hardeners, by keeping solvents in a cool area, free of sources of
ignitions.
Product Material Safety Data Sheets are available and should be
consulted when handling products. These products are for
industrial and professional use only; application directions must be
followed.
Maintenance
Periodically inspect the applied material and repair localized areas
as needed. Consult your HONEST representative for additional
information.

 

Test Standard

Unit

Value

Generic Type

 

 

polyester

Viscosity - mixed

ASTM D 2393

cps

3,500-4,000 @ 77 ºF

Tensile Bond Strength

ASTM D 4541

Psi (MPa)

1,0-1,500 (8-10)

Tensile Strength

ASTM D-638

Psi (MPa)

2,500-3,000 (17-)

Density (wt. per gal)

ASTM D 1475

lbs/gal (kg/liter)

10.0 + 0.2 (1.2 + 0.02)

Moisture Permeability

ASTM E96 Proc. E

perm inch

0.0016

Service Temperature Limits

Immersion/Condensing Fumes Continuous Dry

ºF (ºC)

140 (60) 350 (177)

Tabor Abrasion

CS 17 wheel, 1,000 gm, 1,000 revolution

mg

78

Volatile Organic Compounds

24

lbs/gal (g/l)

3.06 (367.2)

Flash Point

Pensky Martens Closed Cup

ºF (ºC)

93ºF (34ºC)

Important Note
The information in this data sheet is not intended to be exhaustive; any person using the product for any purpose other than that specifically recommended in this data sheet without first
obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at their own risk. All advice given or statements made about the product (whether in
this data sheet or otherwise) is correct to the best of our knowledge but we have no control over the quality or the condition of the substrate or the many factors affecting the use and application
of the product. Therefore, unless we specifically agree in writing to do so, we do not accept any liability at all for the performance of the product or for (subject to law) any loss or damage
arising out of the use of the product. . All products supplied and technical advice given
are subject to our Conditions of Sale. You should request a copy of this document and review it carefully. The information contained in this data sheet is liable to modification from time to time
in the light of experience and our policy of continuous development.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.