General Purpose Aqueous Based Fire Retardant Surface Coating Supplier in China
General Purpose Aqueous Based Fire Retardant Surface Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Fire proof retardant heat resistance coating

VOC Compliant Air Drying Silicone Based Heat Resistant Coating
Two-Component State-OF-The-Art Silicone Coating
Fouling Release Tiecoat

Single Component High Heat Aluminum Coating
High Heat Resistant Black Coating
Silicone Based Heat Resistant Coating
Quick Drying Heat Resistant Aluminium Enamel
Aluminium Heat Resistant Pure Silicone
Air Drying Self-Priming Heat And Corrosion Coating

Compliant VOC High Build Modified Silicone Coating
Solventborne Silicone Coating
Heat Reflective Ceramic Coating

General Purpose Aqueous Based Fire Retardant Surface Coating
Solventborne Silicone Coating
Air Drying Self-Priming Heat And Corrosion Coating
One-Coat Aluminum Fire Resistance Coating
Coloured Heat Resistant Acrylic Silicone
Fire Retardant Coating

  

General Purpose Aqueous Based Fire Retardant Surface Coating

PRODUCT SPECIFICATIONS:

Product
Description
General purpose aqueous based fire retardant surface coating.
Intended Uses To provide protection on a wide variety of substrates and surfaces against
open flame and high radiant heat.
Color Gray
Gloss Flat
Volume Solids 58.0%
Typical Thicknesses 6-120 mil, depending on design
application.
Theoretical Coverage 30.6 ft2/gal at 30 mils
89.0 ft2/gal at 10 mils
Practical Coverage Allow appropriate loss factors.
Method of Application Spray or Brush
Practical
Information
Drying Time Tack Free 1 - 2 Hour depending
on thickness.
Stackable 24 to 36 Hours
depending on thickness.
Full Cure 30+ Days depending
on thickness.
Times are based on 20 mil thickness
at 68°F (20°C) with 50% humidity.
Flash Point None
Product Weight 10.20 lbs / gal
Regulatory
Data
Viscosity Approx. 9,500 cps at 68°F (20°C)
Surface
Preparation
The surface to be coated with HJ PRIMER must be properly prepared in
accordance with good painting practices. The surface must also be clean of
all residual oil, moisture, dust, frost or other contaminates that may have
formed. A recommendation is to power wash exterior surfaces with a water
based cleaning solution and rinse with clean water. When in doubt, use
acetone solvent or tri-sodium phosphate (TSP) solution and thoroughly wipe
down all surfaces to be coated. As the cleaning solution evaporates, make
certain any frost, moisture or oil deposits have been removed. In areas
where spot rusting has occurred, be sure all loose rust, scale, etc. is
removed.
HJ PRIMER is a corrosion resistant and sealant coating. Primers may be
used, if specified, in conjunction with this coating.
Before commencing work over primed surfaces, it is vitally important to
determine the compatibility of HJ PRIMER with the candidate primers.
HJ PRIMER has shown suitable compatibility with the following type of
high quality, properly cured primers:
1. A fast drying, high solids, low VOC, heavy metal free, rust
inhibitive, universal, alkyd primer that has been dried and well
cured for at least 7 days at 70° prior to ECO-FLEX C/G™
application.
2. Most two-component epoxy primers.
3. Aluminum surfaces must be primed with a vinyl-wash primer. Be
sure to follow the surface preparation and application
procedures as recommended by the primer manufacturer.
Application
Mixing Material should always be mixed thoroughly with a
power agitator until uniform.
Airless Spray Recommended for use with the Graco Mark V Airless
Sprayer using a 29 to 31 thousandths Tip with a fluid
pressure of 1,700 p.s.i. (Max), at 1.25 gpm (contact
HJOY Industries Inc. for further Info.).
Air Spray
(Pressure Pot)
Recommended.
Brush Acceptable.
Roller Acceptable.
Thinner Water. However, thinning is not normally required.
Work Stoppage Thoroughly flush all equipment with clean water. All
unused material should be stored in tightly closed
containers.
Partially filled containers will show surface skinning or
viscosity increase if left open.
Clean up Clean and flush all equipment immediately after use
with clean water. It is a good working practice to
periodically flush out the airless spray equipment once
each working day.
All surplus materials and empty containers should be
disposed of in accordance with appropriate local
regulations.
Product
Characteristics
Mechanical mixing of HJ PRIMER prior to use is required to assure
uniformity of blended ingredients and proper material viscosity.
Low or high temperatures may require specific application techniques to
achieve proper dry times, and uniformity.
Surface Temperature must always be 5°F (3°C) above dew point.
HJ PRIMER should be sprayed at a fluid temperature range of 65-80°F
(18-27°C) if possible. Pail and drum heaters can be used to achieve this
temperature.
The finished surface should be uniform and free of voids. Avoid using a
mixture of application methods whenever possible.
Safety
Precautions
This Product is intended for use by professional applicators in industrial
situations in accordance with the advice stated on this bulletin. HJOY
Industries will provide Material Safety Data Sheets to its customers.
All work involving the application and use of this product should be
performed in compliance with all relevant, Health, Safety & Environmental
standards and regulations.
If in doubt regarding the suitability of use of this product, consult HJOY
INDUSTRIES for further advice.

 

 

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.