Hard Abrasive And Weather-Resistant High Gloss Marine Varnish Supplier in China
Hard Abrasive And Weather-Resistant High Gloss Marine Varnish paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Other coating

Concrete Repair Coatings
Easy Sanding Clear Lacquer Sealer
Hydraulic Fluid Resistant Non-slip Finishes
Highly Reflective Marking Paint

Waterborne Thermosetting Glass Paint
Unsaturated Polyester Glass Flake Putty Coating Paint
Coating for Die Casting Aluminum Galvanize and Steel Parts
Semi-Transparent Organic Solvent Stain
Polyester Epoxy Coil Coating
Hard Abrasive And Weather-Resistant High Gloss Marine Varnish

Alkyd Urea Clear Coat
Concrete Aluminum And Steel Marine Structure Epoxy Coating
Zinc Rich Epoxy Powder Coating

Epoxy Powder Coating
Concrete Aluminum And Steel Marine Structure Epoxy Coating
Water Chemical Resistance Tin Lining Coating
Aqua-Loc Ceramic Topcoat
Removable Petroleum-Based Liquid Barrier Coating
Semi-Gloss Precatalyzed Lacquer
Premium High Build Precatalysed Timber Lacquer
Rapid Dry Gloss Enamel
Temperature Indicating Paint
Two Component Oxirane Ester Paint Containing Active Anti-Corrosive Pigments
Molybdenum Disulfide Slick Lubricant Coating

  

Hard Abrasive And Weather-Resistant High Gloss Marine Varnish

PRODUCT SPECIFICATIONS:

PRODUCT DESCRIPTION: A hard abrasive and weather-resistant high gloss marine varnish with an
ultraviolet filter that screens out the destructive rays of the sun. For exterior
or interior use.
BASIC USES: Especially formulated to protect and preserve the natural beauty of woods
used in the construction of yachts and small boats from the ravages of the
sun, sand, sea and weather.
PRODUCT
ADVANTAGES: * Marine grade * Extra long lasting protection
* UV resistant * Dries to a hard and tough finish
* Clear liquid plastic * Resists peeling, flaking and
* Easy to apply contact with household chemicals
TECHNICAL DATA


Percent Solids:

47.15 ± 1% by weight

Finish:

Gloss (over 85º)*

 

54.40 ± 1% by volume

 

*Geometry 60º

Weight / Gallon:

7.38 ± 0.5 lbs.

Viscosity:

130 - 150 cps.

Drying Time:

To touch:

4 hours

Theoretical

 

 

To recoat: 12 hours

Coverage:

600 sq. ft./gal.

Flash Point:

85ºF TOC

Sizes:

55 gallons

 

 

 

5 gallons

Theoretical

 

 

1 gallon

Film Thickness:

2 mils dry, 4 mils wet

 

1 quart

Thinning:

Not normally recommended, but if necessary, add up to 1/2 pint per gallon

 

of

Surface Preparation: All surfaces must be dry, clean and free of
contaminants such as dirt, grease, chalk, mildew, oil, rust, loose or
badly cracked paint.
New Wood: Sand down to a smooth finish with fine sandpaper
following the grain. Remove all sanding dust by vacuuming or
dusting the surface with a “tack” cloth. Fill knot holes and cracks
withHonest joy putty filler for wood; let dry. Sand the filled areas
smooth and remove dust.
Previously Painted Surfaces: This coating is for application to
unfinished wood surfaces or to surfaces previously finished with
this same finish and in good condition. If the previous finish is
not in good condition it must be completely removed with
Honest joy HJ-290. Finish the surface as in New
Surfaces. If surface is in good condition, sand to remove gloss
and touch-up bare areas with this same product. If doubt exists
concerning compatibility of this coating with the previous system,
apply coating to a small area (25 square feet minimum) and allow
to cure and age several weeks. Then inspect for adhesion failure,
wrinkling, lifting or any other sign of incompatibility. If there are
no signs, coating work can proceed.
Mixing: This is a one component coating. Always hand mix
thoroughly with a paddle before application. Do not mix excessively
to avoid air in the coating.
Application: Apply by brush or roller, useHonest joy All Purpose
or conventional or airless spray. Roller
application may require special care to prevent bubbling and more
than one coat to obtain proper thickness. Apply at 4 mils wet film
thickness that will yield 2 mils dry film thickness.
Equipment: Conventional Spray: For suction feed, use
gun with “E” tip and needle and 30 air cap or
equivalent at 35-40 psi atomizing pressure feed. For pressure
feed, use gun with tip and needle and 704 air cap
or equivalent at 35-40 psi atomizing pressure and 5-8 psi fluid
pressure, 3/8” ID material hose, double regulated pressure tank
with oil and moisture separator.
Airless Spray: Minimum of 28:1 ratio pump, .011”-.013”
Limitation: Apply in good weather when air and surface temperature
are above 40ºF and surface temperature is at least 5ºF
above the dew point. For optimum application properties, material
should be between 70º to 100ºF prior to mixing and application.
Note: When multiple coats of product are applied, be sure to sand
lightly between coats with a fine sandpaper and dust clean or vacuum.
Cleanup: Wipe up drips and spatters withHonest joy HJ-906. Clean all equipment with this solution.
Caution: Do not take internally. Close container after each use.
Keep out of the reach of children. Combustible; keep away from
heat and open flame. Avoid prolonged contact with skin and
breathing vapors or spray mist.
Notice: The technical data contained herein are true and accurate
to the best of our knowledge. Published technical data and
instructions are subject to change without prior notice.
M.S.D.S.: Available upon request.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.