Heat Reflective Ceramic Coating Supplier in China
Heat Reflective Ceramic Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us



Honest Joy Coating & Paint
Fire proof retardant heat resistance coating

VOC Compliant Air Drying Silicone Based Heat Resistant Coating
Two-Component State-OF-The-Art Silicone Coating
Fouling Release Tiecoat

Single Component High Heat Aluminum Coating
High Heat Resistant Black Coating
Silicone Based Heat Resistant Coating
Quick Drying Heat Resistant Aluminium Enamel
Aluminium Heat Resistant Pure Silicone
Air Drying Self-Priming Heat And Corrosion Coating

Compliant VOC High Build Modified Silicone Coating
Solventborne Silicone Coating
Heat Reflective Ceramic Coating

General Purpose Aqueous Based Fire Retardant Surface Coating
Solventborne Silicone Coating
Air Drying Self-Priming Heat And Corrosion Coating
One-Coat Aluminum Fire Resistance Coating
Coloured Heat Resistant Acrylic Silicone
Fire Retardant Coating


Heat Reflective Ceramic Coating



HJOY COAT is a unique liquid applied heat reflective and
protective flexible coating. HJOY COAT contains specially
selected ceramic microspheres to reflect and dissipate
solar radiation.
HJOY COAT cures to form a tightly adhering,
weatherproofing coating of outstanding effectiveness
and long-term durability. The cured membrane is
elastomeric, tolerating substrate movement without
cracking or flaking.
! 88% solar radiation reduction. Reduced interior
temperatures. Reduced air conditioning loads.
! Dramatically lower surface temperatures – less
stress due to expansion and contraction - longer
roof life
! Suitable for all types of substrates - especially
effective on concrete and metal roof or wall
! Water-based. Safe to use and easy to clean up.
! Metal Roof Decks
! Metal Wall Surfaces
! Storage Tanks
! Grain Silos
! Concrete Roofs and Walls
Specific Gravity 0.85 +/- 0.05
Consistency Viscous liquid
Solids Wt. 62% Vol. 68%
Elongation 200% at 25º C
Tensile Strength 0.3 (Kgf/mm sq at 25º
Cure Time 2 – 4 hours set time
Colour White
Appearance (Dry) Low Sheen
HJOY COAT meets or exceeds the following test criteria:
R-Value ASTM C-177
Water Vapour Permeability ASTM 1653
Accelerated Weathering
3,000 hours
Water Absorbtion ASTM D-570
20ltr Plastic Pails
2.2 m2 per Ltr @ 300ìm DFT
1.3 m2 per Ltr @ 500ìm DFT
Coverage figures quoted are approximate only and
allowance should be made for wastage.
1. Concrete - Remove all debris and contaminants
from the surface. Optimum preparation will be
achieved by high pressure water blasting (1,000
psi). If water blasting not possible, ensure the
substrate is sound, or carry out repairs using a
polymer modified cement as required. Allow any
repaired areas to cure overnight before coating.
Prime the entire surface using a suitable Concrete
Primer before applying the HJOY COAT.
Metal - Inspect metal surfaces for any signs or
corrosion. Corroded areas must be thoroughly
cleaned and mechanically prepared to remove all
rust scale and surface contaminants. Apply
suitable anti-corrosive metal primer to entire
surface area and allow minimum 4 hours to cure
before top coating.
2. Product Application – HJOY COAT may be applied
using a brush, roller or airless spray. In some
circumstances, particularly if applying by airless
spray equipment, the viscosity of HJOY COAT may
warrant the addition of 5-10% of water for
improved spray viscosity.
In accordance with conventional good coating
practices, it is recommended HJOY COAT be applied
in 2 coats to avoid pin holing and other
imperfections that may result due to surface
Minimum Recommended Thickness - HJOY COAT
is designed to provide long life protection under a
wide variety of atmospheric conditions. The
performance properties of HJOY COAT can be
optimised by adhering to the following DFT (Dry
Film Thickness) recommendations:
Substrate Min. DFT
Metal Wall Cladding 300 ìm
Metal Roof Deck 300 - 500ìm
Cement Wall Render 500 - 700ìm
Concrete Roof Deck: 1.0 mm
* Refer to your Technical Representative for
specific recommendations.
1. Apply only between 18 – 35ºC. If temperatures
exceed this range contact your technical sales
Always wear protective clothing, gloves and goggles
during use. Do not use in unventilated areas. Please
refer to Material Safety Data Sheet for detailed safety
Honestjoy Co. Ltd. warrants the product to be
free from defects in material and workmanship. The seller’s
sole obligation and Buyer’s exclusive remedy in connection
with the products shall be limited, at the seller’s option, to
either replacement of products not conforming to this
warranty or credit to Buyer’s account in the invoiced amount
of the nonconforming products. Any claim under this
warranty must be made by Buyer to the seller in writing within
five days of Buyer’s discovery of the claimed defect, but in no
event later than the expiration of the applicable shelf life, or
one year from the delivery date, whichever is earlier. Buyer’s
failure to notify the seller of such nonconformance as
required herein shall bar Buyer from recovery under this
The seller makes no other warranties concerning this
product. No other warranties, either express or implied, or
statutory, such as warranties or merchantability or fitness for
a particular purpose, shall apply. In no event shall the seller
be liable for consequential or incidental damages.
Any recommendation or suggestion relating to the use
of the products made by the seller, whether in it’s
technical literature, or in response to specific inquiry, or
otherwise, is based on data believed to be reliable;
however, the products and information are intended for
Buyers having requisite skill and know-how in the
industry, and therefore it is for the Buyer to satisfy itself
of the suitability of the products for its own particular
use, and it shall be deemed that Buyer has done so, at
its sole discretion and risk. Variation in environment,
changes in procedures of use, or extrapolation of data
may cause unsatisfactory results. The seller cannot
guarantee that colour will conform to sample, if



Contact Us
Honest Joy Coating & Paint. All rights reserved.