products: polyurethane epoxy  Nitrocellulose UV unsaturated PE paint coating manufacture Shenzhen China  
Home About Us Products Contact Us
 



Honest Joy Coating & Paint

Epoxy System
Structural Steel Epoxy Primer
Structural Steel Epoxy Top Coat
Epoxy Sealer
Floor Coating
Silane Penetrating Sealer
Primer
Epoxy Protective Coating
Flexible Epoxy Coating.htm
Touch-Up Epoxy Rebar Coating
Moisture Tolerant Epoxy Primer
Corrosion Resistant Coating
Heat Resistant Coating
Elastomeric Cement Coating
Glass Flaked Epoxy Coating
Breathable Masonry Coating

Polyurethane System
Sandable Sealer Basecoat
Coatings for musical instruments
Primers for wood
Coatings for kitchen cabinets
Lead and chrome free wood coatings
Fire retardant wood coatings
Coatings for furniture
Coatings for Speaker
Aliphatic Weather Resistant Polyurethane
Structural Steel Weather Resistant Paint
Acrylic Coating
Faster Drying Coatings
Nitrocellulose coatings (NC) System
Lacquers for wood
Faux Finishing
Glaze
Nitrocellulose coatings
NC Coatings for furniture
Coatings for picture frames
Non toxic coatings

Transfer printing
Thermo Transfer Printing
Water Transfer Printing
Cubic Emulation Covering

Others
UV coatings for wood
Coatings for metal
Teflon Modified Corrosion Resistant Coating
Hydro-Ester Coating
Zinc Rich Primer
Rust Inhibitive Metal Primer
Sprayable Aromatic Polyurea
Plastic Paint
  


Hydro-Ester Coating

 Shenzhen China Suppliers Products: Hydro-Ester Coating

Name: Hydro-Ester Coating
Data Sheet:
specification "ADVANTAGES: Feiyang -70-9 can be applied to concrete, wood or steel. Will cure and adhere in damp enviroments. Feiyang -70-9 has excellent resistance to water, chemicals and hydrogen sulfide. PHYSICAL PROPERTIES: Color Fed Standard No. 595, Color No. 26622 Gray - other colors available as special order products Pot Life 30 mins 72F Tensile Strength ASTM D-638 5000 psi min. (14 days) Tensile Elongation ASTM D-638 5% min (14 days) Compressive Strength ASTM C 109 Mod. 7,500 psi (7 days) Viscosity #6 spindle @ 50 rpm 12,000 cps +\- 1000 Solids Content 100% Tack Free Time 3hrs max @ 75F Abrasion Resistance ASTM D 968 60 liters per mil min (14 days) Dielectric Constant 1 kiloHertz 1 megaHertz 4.65 4.15 Dissipation Factor 1 kiloHertz 1 MegaHertz 0.0216 0.092 Volume Resistivity 8.1 * 1014 ohm-inches Surface Resistivity 1.5 * 1015 ohms Electric Strength Volt per mil 440-465 SURFACE PREPARATION: Steel Surfaces: Steel surfaces should be abrasion blasted as specified by the SSPC SP-6 Commercial Blast Finish. All work blasted shall be coated the same day with Feiyang -408 Zinc Rich Primer. Concrete Surfaces: Concrete surfaces shall be cleaned to remove dirt, curing compounds,existing coatings or laitance to provide a clean, sound bonding surface. Cleaning may be accomplished with Feiyang -Masonry Cleaner and water blasting, acid etching and water blasting, abrasion blasting, or other method that would achieve a similar result. MIXING: Stir Components ""A"" and ""B"" thoroughly before mixing. Combine two (2) parts by volume of ""A"" with one (1) part by volume of ""B"" (mixing ratio 2:1). Mix for not less than three (3) minutes with a slow speed drill (300 to 600 rpm), and a Feiyang -Mixing Paddle. APPLICATION: Feiyang -70-9 may be applied by brush, roller or spray. All spray equipment must employ traps to prevent water and oil from contaminating coating. COVERAGE: Feiyang -70-9 will cover approximately 200 sq. ft. per gal. Per coat at a thickness of eight (8) mils, dependent upon surface texture. For best results, use two (2) coats. PACKAGING: Feiyang -70-9 is packaged in three (3) gallon, and fifteen (15) gallon units. LIMITATIONS: Feiyang -70-9 should not be applied when surface temperatures are below 40F. SHELF LIFE: 2 years CAUTION: WARNING! A Component contains epoxy resin. DANGER! ""B"" Component contains alkaline amines; strong sensitizer. May cause skin sensitization or other allergic responses. Use with good ventilation, particularly if material is heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves and/or barrier creams. Keep container closed when not in use. Wash thoroughly after handling. FIRST AID: In case of skin contact, immediately wash with soap and water. In case of eye contact, flush eyes with copious amounts of water for at least fifteen (15) minutes. Remove contaminated clothing and shoes. If irritation persists, seek medical attention. Wash clothing before reuse."

Inquiry on Hydro-Ester Coating
 
Honest Joy Coating & Paint. All rights reserved.