Moisture Resistant Lacquer Supplier in China
Moisture Resistant Lacquer Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Industry protect coating

Ultra-high Build Single-component Coal Tar Mastic
Ultimate Chemical Resistant Coating
Two-pack High Solids High Performance Maintenance Coating
Two-component Chemical Resistant Enamel

Surface Tolerant Self-priming Corrosion Inhibitor Coating
Structrial Steel Primer
Sovent Borne Alkali Resisting Primer
Solvent-borne Aluminium Finish
Solvent Based Anti-slip Floor Paint
Single Component Penetrating Corrsion Inhibitor
Single Component Industrial Maintenance Primer

Multifunctional Chemical Resistant Coating
Moisture Resistant Lacquer
Pipe Coating
Anti Static Coating
Anti-Static Conductive Primer




  

Moisture Resistant Lacquer

PRODUCT SPECIFICATIONS:

Moisture Resistant
Lacquers are self sealing general purpose
topcoats specially designed for resistance
to moisture and household
chemicals.
Advantages:
• Meets the rule for wood
finishes as packaged*
• Excellent moisture resistance
• Excellent resistance to household
chemicals
• Self sealing
• Non-photochemically reactive
• Excellent adhesion
• Excellent cold check resistance
• Excellent print resistance


CHARACTISTICS
Gloss: Gloss Full
MRE 30-34 units
DRE 17-21 units
Volume Solids: 16 ± 2%
Viscosity:
28-33 seconds
Recommended film thickness:
Mils Wet 5.0 - 6.0
Mils Dry 0.8 - 1.0
Spreading Rate (no application loss)
225-361 sq ft/gal @ 0.8-1.0 mil DFT
Drying (77°F, 50% RH):
To Touch: 10-15 minutes
To Handle: 30-45 minutes
To Recoat: 60 minutes, do not
exceed 12 hours
Force Dry:
To Sand 10 minutes at 140°F
To Recoat: 15 minutes at 140°F
To Pack: 60 minutes at 140°F
Flash Point: 22°F
Package Life: 3 years, unopened
Air Quality Data:
Non-photochemically reactive
Volatile Organic Compounds (VOC)
as packaged, maximum
5.63 lb/gal, 675 g/L
3.19 lbs VOC/lb solids
Hazardous Air Pollutants
as packaged, maximum
less than 0.8 lbs per pound of solids

SPECIFICATIONS
Wood (interior only): Must be clean, dry,
and finish sanded. Substrate should be
free of grease, oil, dirt, fingerprints, and
any contamination to ensure optimum
adhesion and coating performance properties.
Moisture content of wood should be 6 to
8%.
Testing: Due to the wide variety of substrates,
surface preparation methods,
application methods, and environments,
the customer should test the complete
system for adhesion and compatibility
prior to full scale application.
Wood Finishing System:
Three Coat System
1. Moisture Resistant Lacquer, dry one
hour, sand with stearated paper
2. Moisture Resistant Lacquer, dry one
hour, sand with stearated paper
3. Moisture Resistant Lacquer
Sanding Sealer System
1. Vinyl Sanding Sealer, HJ26, HJ-558,
or HJ-551, dry 30 minutes and
sand
2. Moisture Resistant Lacquer, dry one
hour
3. Moisture Resistant Lacquer
The 3 coat system is ideal for customers
who like to limit the number of finishing
materials they must have on hand to one
product.
APPLICATION
Typical Setups
Reduction: Normally not required. If reduction
is needed use Compliant
Lacquer Thinner, HJ8788 or HJ8789.
Lacquer thinner HJ-221 or K1 may also
be used, but are not compliant.

May be applied by:
Conventional
Airless Spray
Warm Spray
Curtain Coating

Conventional Spray:
Air Pressure .......................... 50-65 psi
Fluid Pressure ......................12-15 psi
Airless Spray:
Air Pressure .................... 10-1800 psi
Tip Size ...................................... .009-013
Cleanup:
Clean tools/equipment immediately after
use with complying lacquer
thinner, HJ-0090 or HJ8789. Lacquer
thinner, K1 or HJ-221, may also be used,
but are not compliant.
Follow manufacturer's safety recommendations
when using any solvent.
Moisture Resistance Test:
Birch panels were finished with 3 coats of
Gloss Moisture Resistant Lacquer, with 1 hour
drying between coats. The front, back and all
sides were finished.
1. An "X" cut was made through the finish to
the wood. This was covered with a wet
synthetic sponge for 16 hours. After
sponge removal, a whitening appeared, on
the cut, which disappeared after 2 hours.
2. Finish Test, F-4, Detergent and Water
Test—no effect.
Performance Tests:
Cold Check Resistance ................ cycles
Print Resistance .............................. No print
3.0 mils dft, 18 hours air dry, at 1 psi at 77°F in
direct contact with 8 oz. duck cloth.
SPECIFICATIONS
Product Limitations:
• Apply all coats within a 12 hour period or
lifting may occur.
• Apply directly to bare or stained wood for
best adhesion and moisture results. Adhesion
may be impaired and resistance to
moisture lowered if used over lacquer
sealer. If a sealer is desired use Sher-
Wood Vinyl Sealer, HJ26, HJ-558,
or HJ-551.
• Customer urged to pretest system under
shop conditions.
• Sand and remove sanding dust between
each coat.
• Not recommended for exterior use.
• To maintain compliance only reduce
with compliant reducers.
Household Chemicals Test
Maple panels were finished with 3 coats of
Gloss Moisture Resistant Lacquer, with 1 hour
drying between coats. After film was aged
30 days at 77°F, 5 drops of each item were
placed under a watch glass for one hour. The
film was rinsed with water, washed with soap
and water, dried and wiped with Naphtha
to remove items not removed with water.
After removal, the finish was examined and
the following results noted:
Household Ammonia ........ slight haze/dulling
Vinegar ............................... no visual effect
Lipstick ................................ no visual effect
Lemon Juice ........................ no visual effect
50% Ethyl Alcohol ............... no visual effect
Mercurochrome 2% ............ no visual effect
Washable Blue Ink .............. no visual effect
Mustard ............................... no visual effect
Oil Base Paint ...................... no visual effect
Latex Emulsion Paint ........... no visual effect
Naphtha ................... no visual effect
Turpentine ........................... no visual effect
Orange Crayon ................... no visual effect
Carbon Tetrachloride .......... no visual effect
Mayonnaise ........................ no visual effect
10% Sodium Carbonate ...... no visual effect
Sour Milk ............................. no visual effect
Margarine ............................ no visual effect
Butter .................................. no visual effect
Water .................................. no visual effect
Grease (Cooking fat) .......... no visual effect
CAUTIONS
FOR INDUSTRIAL SHOP APPLICATION
Thoroughly review product label for safety
and cautions prior to using this product.


Note: Product Data Sheets are periodically
updated to reflect new information
relating to the product. It is important that
the customer obtain the most recent
Product Data Sheet for the product being
used. The information, rating, and
opinions stated here pertain to the material
currently offered and represent the results
of tests believed to be reliable. However,
due to variations in customer handling
and methods of application which
are not known or under our control, The
Honestjoy Company cannot make
any warranties as to the end result.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.