Phenolic Heavy Duty Gym Floor Finish Supplier in China
Phenolic Heavy Duty Gym Floor Finish paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Phenol coating

VOC Compliant Phenolic Coating
Marine Spar Varnish
Rust Inhibitive Phenolic Modified Alkyd Primer
Phenolic Primer

Pigmented Short Phenolic Modified Alkyd Primer
Phenolic Two Component Epoxy Coating
Phenolic Modified Primer
Phenolic Heavy Duty Gym Floor Finish
Phenolic Alkyd Metal Primer
Two-Component Amine Adduct Crued Phenolic Epoxy Paint

Superior Solvent Chemical and Elevated Temperature Resistance Phenolic Coating
Quick Drying Phenolic Modified Alkyd Based Primers
Epoxy Phenolic Topcoat

Reinforced Hybrid Epoxy Phenolic Lining
Quick Drying Phenolic Modified Alkyd Based Primers
Two-Component Amine Adduct Crued Phenolic Epoxy Paint
Moisture Tolerant Lining
Baking Cross-Linked Epoxy-Phenolic Coating
Air Dry Phenolic Coatings

  

Phenolic Heavy Duty Gym Floor Finish

PRODUCT SPECIFICATIONS:

A premium quality, penetrating finish for interior wood and wood products,
particularly floors. Lead, mercury and chromate free.
For industrial, commercial and residential use on new or unpainted interior wood
surfaces. For use on properly prepared surfaces of woodwork, floors and wood trim.
Phenolic Heavy Duty Gym Floor Finish is a low viscosity, penetrating wood
finish for use where a heavy duty, tough, water repellent, mar resistant finish is desired.
Penetrates into the wood fibers to reinforce, seal and waterproof. Reduces wearing,
fraying and staining of the wood surface. Easy to apply. Lead, mercury and chromate
free.
Clear
Satin to Gloss depending on application technique.
Nonvolatile - By weight - 36.7 + 1.0%
By volume - 30.7 + 1.0%
VOC (Calculated) - 4.45 lbs./gal.
533 grams/liter
Flash Point - 104oF
Weight per gallon - 7.0 + 0.2 lbs.
Recommended Film Thickness - This product is designed as a penetrating finish and
film thickness cannot be accurately measured.
Theoretical Coverage - Coverage will vary with the porosity of the surface and should
be approximately 500 square feet per gallon.
Method - Brush or flat applicator
Thinner - Thinning is not recommended.
Dry time @ 75oF - To touch - 1 hour
To handle - 4 hours
To recoat - 24 hours
Consists of - 1 Gallon Unit 5 Gallon Unit
Unit Shipping Weight 8 lbs. 38 lbs.
Shelf Life - 12 months minimum from date of manufacture when maintained in
protected storage @ 40-100oF (subject to reinspection thereafter).
APPLICATION INSTRUCTIONS

Limitations: Apply in good weather when air and
surface temperatures are above 40oF and surface temperature
is at least 5oF above the dew point. For
optimum application properties, material should be
between 70 to 100oF prior to mixing and application.
Maintain unmixed material in closed containers in
protected storage at 40 - 100oF. NOTE: Not recommended
for exterior use.
Surface Preparation: Good surface preparation is
essential to a satisfactory coating system. Surfaces to
be coated must be clean and dry. Remove all dust, dirt,
oil, wax, polish and any other surface contamination.
New or Unfinished Wood - New wood should be
sanded with fine sandpaper following with the grain.
Remove all sanding dust by vacuuming and/or dusting
the surface with a “tack” cloth.
Previously Finished Surfaces - This coating is for
application to unfinished wood surfaces only. Certain
fillers and putties may present compatibility problems
when using this coating. If doubt exists concerning
compatibility of this coating with the filler or putty, apply
coating to a representative area (25 square feet minimum)
and allow to cure and age several weeks. Then
inspect for adhesion failure, wrinkling, lifting, blistering
or any other sign of incompatibility. If there are no
signs, coating work can proceed.
Mixing: This is a one component coating. Always
hand mix thoroughly with a paddle before application.
Do not mix excessively to avoid entraining air in the
coating.
application viscosity. Thinning is not recommended.
See cleanup paragraph for cleanup thinner.
Application: Apply by brush or lambswool applicator.
Roller application may cause bubbling. Application by
spray is not recommended. Allow finish to penetrate
surface for 10 to 15 minutes and wipe off excess with
a clean, lint free cloth. Apply at a spreading rate of
approximately 500 square feet per gallon. The recommended
second coat can be applied after the first coat
has dried 24 hours. Sand lightly between coats and
remove all dust.
Equipment: Use a good quality bristle brush or
lambswool applicator. Spray application is not recommended.
Cleanup: Clean all equipment immediately after use
with HJ-175.
Safety: Safe storage, handling and use dictate that
adequate health and safety precautions be observed
with this product and any recommended thinners. User
is specifically directed to consult the current Material
Safety Data Sheet for this product as well as precautions
contained on product labeling.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.