Premium High Build Precatalysed Timber Lacquer Supplier in China
Premium High Build Precatalysed Timber Lacquer paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Other coating

Concrete Repair Coatings
Easy Sanding Clear Lacquer Sealer
Hydraulic Fluid Resistant Non-slip Finishes
Highly Reflective Marking Paint

Waterborne Thermosetting Glass Paint
Unsaturated Polyester Glass Flake Putty Coating Paint
Coating for Die Casting Aluminum Galvanize and Steel Parts
Semi-Transparent Organic Solvent Stain
Polyester Epoxy Coil Coating
Hard Abrasive And Weather-Resistant High Gloss Marine Varnish

Alkyd Urea Clear Coat
Concrete Aluminum And Steel Marine Structure Epoxy Coating
Zinc Rich Epoxy Powder Coating

Epoxy Powder Coating
Concrete Aluminum And Steel Marine Structure Epoxy Coating
Water Chemical Resistance Tin Lining Coating
Aqua-Loc Ceramic Topcoat
Removable Petroleum-Based Liquid Barrier Coating
Semi-Gloss Precatalyzed Lacquer
Premium High Build Precatalysed Timber Lacquer
Rapid Dry Gloss Enamel
Temperature Indicating Paint
Two Component Oxirane Ester Paint Containing Active Anti-Corrosive Pigments
Molybdenum Disulfide Slick Lubricant Coating

  

Premium High Build Precatalysed Timber Lacquer

PRODUCT SPECIFICATIONS:

DESCRIPTION: Classicwood HJ-442 is a single pack precatalysed modified N/C lacquer,
available in a range of gloss levels.
FEATURES: _ Fast drying
_ Fast sanding
_ Smooth silky feel
_ Abrasion and scuff resistant
_ Alcohol and stain resistant
_ Pale colour
APPLICATION AREAS: As a finish for built in furniture, shop fittings, doors, cabinets, wall
panelling, partitions and most interior woodwork.
TYPICAL SYSTEMS: Many excellent systems may be used for finishing with Classicwood HJ-442. As a guide, the following have been selected:
Natural Finish Unstained:
i) Spray a double header coat of HJ-0080and allow to dry 1 hour.
ii) Sand with 280 – 3 grit paper and dust off.
iii) Spray 1 or 2 double header coats of Classicwood HJ-442 of desired gloss level.
Natural Finished Stained:
i) Stain with appropriate colour allow to dry the required drying
time.
ii) Spray a double header coat of HJ-0080and allow to dry 1 hour.
iii) Sand with 280 – 3 grit paper and dust off.
iv) Spray 1 – 2 double header coat of Classicwood HJ-442 of desired gloss level.
Full Finish:
i) Fill grain with suitable wood grain filler of desired colour and allow to dry as recommended by
manufacturer.
ii) Stain with the appropriate colour Stain HJ-880 and allow to dry the required drying time.
iii) Spray a double header coat of HJ-0080and allow to dry 1 hour.
iv) Sand with 280 – 3 grit paper and dust off.
v) Spray 1 – 2 double header coats of Classicwood HJ-442 of desired gloss level.

APPLICATION
For maximum build do not thin. May be thinned up to
10% if required and applied by conventional spray at an
atomizing pressure of 350 kPa. Suitable for application
by curtain coating, airless spray, pressure pot or gravity
feed.
THINNING: 265 Thinner.
CLEANING: Clean equipment with 265 Thinner
immediately after use.
APPROXIMATE COVAGE: 11.5 m2 per litre at 100
mm wet film thickness. (Does not allow for application
losses.)
CONTAIN SIZE
4 litre litre 0 litre
PRECAUTIONS
Classicwood HJ-442 contains flammable solvents. Keep
away from heat and open flame. When applying in a
confined space, use an air line respirator. In common
with other organic solutions, contact with the skin should
be avoided and protective clothing worn and normal
hygiene standards should be observed.
NOT RECOMMENDED
Do not recoat with standard nitrocellulose lacquers (not
precatalysed). Do not apply over sanding sealers other
than HJ-0080 or Urethane Sealer HJ-900A, otherwise
whitening could occur under adverse conditions.
GENAL RECOMMENDATIONS
This finish should not be used in areas exposed to
extreme conditions of temperature, moisture or abrasion
as frequently met in kitchens and bathrooms. During hot
weather, rapid drying may cause flow problems and
dusting or dry spray on large areas.
With low temperatures, heavy coats often cannot be
applied on vertical surface without sagging and runs. A
reduction in pot pressure can assist by increasing the
evaporation of the solvent.

If a further coat of Classicwood HJ-442 is required, the first
coat must be thoroughly sanded.
Technical information given verbally or in writing is based on knowledge and research, given in good faith and believed to be reliable, but no guarantee of
accuracy is made or implied. Since methods and conditions of use are beyond our control, all merchandise is sold and received subject to the condition that
our liability whether express or implied for any defect in quality, or for any lack of fitness for the specified use thereof, is limited to the return of the purchase
price if written claim is made within 14 days from date of delivery. It is recommended that the user makes his or her own tests to determine the suitability of
the product for his own requirements. Freedom from patent restrictions is not implied.

Gloss Levels:

10, 30, 50, 100%

Drying Time:

Approximate air dry times at 25 oC minutes

Print Free:

1 hour

Sanding: Oiling:

2 hours Can be force dried at 49 oC – 60 oC

Recoating Time:

1 hour minimum

Shelf Life:

12 months minimum

Flash Point:

< 8 oC. Classification 3. Setaflash

 

closed cup method

Durability:

Excellent interior use.

Resistance Properties

Abrasion:

Excellent

Heat:

Good

Solvent:

Good except for esters and

 

ketones

Alcohol:

Good

Perfume:

Good

Water & Steam:

Fair

Stain:

Good

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.