Premium Red Oxide Rust Preventative Primer Supplier in China
Premium Red Oxide Rust Preventative Primer Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Red Oxide Primer

Chlorinated Rubber Red Oxide Primer
Epoxy Micaceous Iron Oxide Coating
Micaceous Iron Oxide Pigmented Two-Pack Epoxy Coating
Modified Alkyd Based Anticorrosive Red Oxide Metal Primer
Drying Oil Gray Oxide Primer
Oil Red Oxide Primer
Red Oxide Rust Preventative Primer
Red Oxide Finish
Lead Free Red Oxide Primer
Red Oxide Quick Dry Primer


  

Premium Red Oxide Rust Preventative Primer

DESCRIPTION: The premium red oxide, rust preventative primer for ferrous metals provides excellent wetting characteristics and high build and can be applied over light residual rust that cannot be removed by wire brushing or sandblasting. Primarily used for priming structural steel in the field. For handrails and other metal surfaces subject to friction-type contact, use Honest(43-5).
PRODUCT INFORMATION
SOLVENT TYPE RESIN TYPE
Paint thinner Alkyd
FINISH (ASTM D 523)
Flat
COLOR
Red oxide
VISCOSITY AT 77°F/25°C (ASTM D 562)
85-90 KU
MAXIMUM VOC CONTENT
300 g/L (as supplied)
SOLIDS BY VOLUME (ASTM D 2697) SOLIDS BY WEIGHT
60.0% ± 2% 77.0% ± 2%
WEIGHT P GALLON (ASTM D 1475)
12. lbs.
COMPOSITION BY WEIGHT
Pigment - 53.0% Vehicle - 47.0%
Rust inhibitive pigments............. 17.0 Alkyd resins & oils ...................... 26.0
Red oxide pigments ..................... 8.0 Thinners & additives................... 21.0
Reinforcing pigments ................. 28.0
RECOMMENDED FILM THICKNESS P COAT
Wet: 3.2 mils Dry: 2.0 mils
PRACTICAL COVAGE P COAT AT RECOMMENDED DRY FILM
THICKNESS
500-550 sq. ft. per gallon, depending on surface conditions.
AVAGE DRY TIME AT 77°F/25°C (ASTM D 1640)
To touch: 2-4 hours
Recoat: 24 hours
APPLICATION EQUIPMENT
Brush, roller, airless spray, HVLP spray
PACKAGING
Quart, one-gallon, five-gallon containers
MATIAL SAFETY DATA SHEET
SURFACE PREPARATION
All surfaces must be cured, clean, dry, and free from dirt, dust, rust, stains,
grease, oil, wax, and other contaminants. Remove all loose, peeling, or
chalky paint by sanding, scraping, high-pressure washing, sandblasting or
other appropriate methods. Glossy surfaces should be dulled to provide a
roughened surface for good adhesion.
SPECIAL INSTRUCTIONS
• CAUTION: Scraping or sanding surfaces of older buildings (especially pre-
1978) may release dust containing lead or asbestos. EXPOSURE TO
LEAD OR ASBESTOS CAN BE VY HAZARDOUS TO YOUR HEALTH.
Always wear appropriate personal protective equipment during surface
preparation, and finish cleanup of any residues by water-washing all
surfaces.


• This product can neither cause nor prevent or cure the growth of mold,
mildew, or other forms of fungus. Excessive moisture and inadequate
ventilation are the main conditions that promote their growth. Correct any
such conditions before painting.
• Sandblasted or newly cleaned metal must be prime-coated the same day
to prevent recontamination.
THINNING RECOMMENDATIONS
Up to one pint of paint thinner per gallon.
STORAGE
Store in a dry area. Protect from freezing. Extreme temperatures may cause
paint to become unusable. For example: Freezing and thawing may cause
paint to gel, and high heat may cause a solid skin to form.
CLEANUP
Paint thinner, where allowed. Dispose of waste in accordance with all
applicable laws and regulations.
DISPOSAL
For information on local options to dispose of unwanted, leftover paint, call
+86-755-26404303, or log onto www.polyurethane-paint.com.

 

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.