Quick Drying Clear Urethane Alkyd Varnish Supplier in China
Quick Drying Clear Urethane Alkyd Varnish paint coating manufacture Shenzhen China  
Home About Us Products Contact Us



Honest Joy Coating & Paint
Alkyd coating

Urethane-Modified Alkyd Primer
Urethane Alkyd Enamel
Urethane Alkyd Based Toopcoat
Epoxy Ester Modified Alkyd Primer

Superior Quality Alkyd Glaze
Speedy-Dry Alkyd Enamel
Silicone Modified Alkyd Enamel
Semi-Transparent Organic Solvent Stain
Rust-Inhibitive Patented Acrylic Modified Alkyd Enamel
Quick-Drying Styrenated Alkyd Paint

Alkyd Urea Clear Coat
Transparent Modified Alkyd Sealer
Alkyd Semigloss Finish
Transparent Modified Alkyd Sealer
Quick Drying Modified Alkyd Based Primer
Rust Preventing Primer
Quick Drying Clear Urethane Alkyd Varnish
Versatile Finish Coat Based On Long Oil Alkyd Resin Exceptionally Durable Fast Drying Alkyd Paint
Fast Dry Alkyd Metal Primer
Alkyd Gloss Enamel
High Gloss Alkyd Aluminum Paint
Alkyd Baking Enamel


Quick Drying Clear Urethane Alkyd Varnish


Description: Honestjoy’S MARINE VARNISH 022 is a quick-drying clear urethane alkyd varnish.
Recommended use: On new wood as well as over previously varnished wood, interior and exterior, above
the waterline.

Colours/Shade nos: Transparent
Finish: Glossy
Volume solids, %: 46 ± 1
Theoretical spreading rate: 18.4 m²/litre - 25 micron
738 sq.ft./gallon - 1 mil
Flash point: 38°C/100°F
Specific gravity: 0.9 kg/litre - 7.5 lbs/gallon
Dry to touch: 2-3 hours at °C/68°F
V.O.C.: 430 g/litre - 3.6 lbs/gallon

Application method: Best results will be obtained with a flat varnish brush. Spray application is possible
with most types of spray equipment after thinning, but this application method is
mainly subject to specific local conditions, so no general guidelines can be given.
Cleaning of tools: Thinner 019
Indicated film thickness, dry: 25 micron/1.0 mil
Indicated film thickness, wet: 50 micron/2 mils
Recoat interval, min: 6 hours (°C/68°F)
Recoat interval, max: See REMARKS overleaf
Safety: Handle with care. Before and during use, observe all safety labels on packaging and
paint containers. Avoid inhalation, avoid contact with skin and eyes, and do
not swallow. Take precautions against possible risks of fire or explosions as well as
protection of the environment. Apply only in well ventilated areas.
SURFACE New wood: Saturate the dry surface with a commercial antimould fluid, preferably made from
PREPARATION: fungicide dissolved in white spirit. Apply one coat Honestjoy’S MARINE VARNISH 022 thinned
with % Thinner 019. Apply a second coat Honestjoy'S MARINE VARNISH 022 thinned
5-10%. Finally apply 3-5 coats Honestjoy'S MARINE VARNISH 022 undiluted.
For the best result rub with dry or wet fine sandpaper and dust off between coats for a smooth
Previously varnished wood: Wash surface with suitable cleaning agent. Do not use detergents
unless they are removed completely, as otherwise residues can spoil the drying properties and
give adhesion problems. Proceed as for new wood. In some cases the antimould treatment and
the first thinned coats can be omitted.
Note: Ammonia water may discolour oak, mahogany and teak.
APPLICATION The surface must be completely clean and dry. Do not apply under humid conditions or at
CONDITIONS: temperatures below 5°C/41°F. The moisture content in the wood should not exceed 16%.
Recoating: Maximum recoating intervals related to later conditions of exposure (°C/68°F):

Surface temperature


Recoated with
(Quality nos only)







If the maximum recoating interval is exceeded, rub down the surface to ensure adhesion.


Contact Us
Honest Joy Coating & Paint. All rights reserved.