Quick Drying Heat Resistant Aluminium Enamel Supplier in China
Quick Drying Heat Resistant Aluminium Enamel paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Fire proof retardant heat resistance coating

VOC Compliant Air Drying Silicone Based Heat Resistant Coating
Two-Component State-OF-The-Art Silicone Coating
Fouling Release Tiecoat

Single Component High Heat Aluminum Coating
High Heat Resistant Black Coating
Silicone Based Heat Resistant Coating
Quick Drying Heat Resistant Aluminium Enamel
Aluminium Heat Resistant Pure Silicone
Air Drying Self-Priming Heat And Corrosion Coating

Compliant VOC High Build Modified Silicone Coating
Solventborne Silicone Coating
Heat Reflective Ceramic Coating

General Purpose Aqueous Based Fire Retardant Surface Coating
Solventborne Silicone Coating
Air Drying Self-Priming Heat And Corrosion Coating
One-Coat Aluminum Fire Resistance Coating
Coloured Heat Resistant Acrylic Silicone
Fire Retardant Coating

  

Quick Drying Heat Resistant Aluminium Enamel

PRODUCT SPECIFICATIONS:

Composition
HJ-27 ALUMINIUM ENAME is a synthetic resin based quick drying bright silver paint designed for
industrial use as a coating for steel, and also for use as a drum or equipment enamel.
Uses and
Properties
As a finishing coat over a wide range of anti-corrosive primers or primer surfacers. Features include:
_ High reflectivity of heat and U.V.
_ Extremely fast drying
_ Brilliant silver finish
_ Good obliteration in thin films
_ Heat resistance to 0oC
Typical
Applications
As an economical finish over primed or unprimed steel surfaces. Typical areas of use are drum
manufacturing and reconditioning, truck wheels, agricultural and earthmoving equipment parts.
Typical
Systems
Substrate Surface Preparation Typical Systems dft mm
Structural steel
Abrasive blast clean.
1st Coat: HJ-76
2nd Coat: HJ-27 ALUMINIUM ENAME
3rd Coat: HJ-27 ALUMINIUM ENAME
40-50
-25
-25
Structural steel
(Heat resistant
system)
Mild steel
(General Industrial
use)
Abrasive blast clean.
Remove rust, clean and
degrease.
1st Coat: HJ-68
2nd Coat: HJ-27 ALUMINIUM ENAME
1st Coat: HJ-27 ALUMINIUM ENAME
2nd Coat: HJ-27 ALUMINIUM ENAME
50
-25
-25
-25
Galvanised steel
Solvent degrease and
abrade and clean. Sweep
blasting recommended for
larger sections.
1st Coat: HJ-002
2nd Coat: HJ-27 ALUMINIUM ENAME
6-12
-25

General Data

 

Weathering

Good exterior durability

Finish

Metallic sheen

Chemical Resistance

Not recommended.

Abrasion Resistance

Poor

Immersion

Not recommended

Temperature Range

Up to 0oC dry heat.

Colour

Bright Aluminium

Topcoating

Not normally topcoated

Shelf Life

12 months from date of shipment if stored indoors at 4°C to 38°C.

Application Data
Theoretical Coverage 8.3 Sq Metres per litre at 25 mm dry film thickness. (Wet film thickness 125 μm).
Volume Solids 21%
Drying Time
(@ 25ºC, 50% R.H.)
Dust free: 5-10 Minutes; Touch Dry: 10-15 Minutes; Hard dry: 12-16 Hours.
Minimum Recoating time: 16 Hours. Maximum Recoating time: Fully recoatable but
aged films must be free of chalk and dirt before recoating. N.B.: If product has been
subjected to heat then the coating should be abraded before recoating.
NOTE: The figures quoted for drying and recoating times are not definitive. They are
dependent on site conditions, ambient and surface temperatures, weather and
ventilation.
Mixing Stir thoroughly until uniform.
Thinning Conventional spray application: Use up to 25% HJ-64.HJ-612 may be
used for hot windy conditions.
Equipment
Conventional spray: Thinning not normally required. Use 70-175 kPa pot pressure and
340-4 kPa atomising pressure.
Airless spray: Thinning not required. Use tip orifice 225-275 microns, (0.009”-0.011”)
thou. Apply at 14-17 MPa atomising pressure.
Brush or Roller: Thinning not required. Suitable for small areas only
Safety Precautions Contents are flammable. Keep away from fire or naked flame or sparks. Keep away
from children. Read Material Safety Data Sheet. When mixing or applying wear
goggles and gloves and ensure good ventilation. When spraying, wear appropriate
protective clothing and air supply. If splashed on skin, wash with soap and water.
Adequate forced ventilation must be provided in confined spaces.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.