Quick-Drying Styrenated Alkyd Paint Supplier in China
Quick-Drying Styrenated Alkyd Paint paint coating manufacture Shenzhen China  
Home About Us Products Contact Us



Honest Joy Coating & Paint
Alkyd coating

Urethane-Modified Alkyd Primer
Urethane Alkyd Enamel
Urethane Alkyd Based Toopcoat
Epoxy Ester Modified Alkyd Primer

Superior Quality Alkyd Glaze
Speedy-Dry Alkyd Enamel
Silicone Modified Alkyd Enamel
Semi-Transparent Organic Solvent Stain
Rust-Inhibitive Patented Acrylic Modified Alkyd Enamel
Quick-Drying Styrenated Alkyd Paint

Alkyd Urea Clear Coat
Transparent Modified Alkyd Sealer
Alkyd Semigloss Finish
Transparent Modified Alkyd Sealer
Quick Drying Modified Alkyd Based Primer
Rust Preventing Primer
Quick Drying Clear Urethane Alkyd Varnish
Versatile Finish Coat Based On Long Oil Alkyd Resin Exceptionally Durable Fast Drying Alkyd Paint
Fast Dry Alkyd Metal Primer
Alkyd Gloss Enamel
High Gloss Alkyd Aluminum Paint
Alkyd Baking Enamel


Quick-Drying Styrenated Alkyd Paint


ADescription: HJ511 is a quick-drying, styrenated alkyd paint. Hardwearing
and resistant to sunlight, salt water, and to oil splashes, but not to aromatic
hydrocarbons, such as certain types of petrol (gasoline).
Recommended use: As a general purpose finishing coat, interior and exterior, on steel decks, stairways,
catwalks, etc., in mildly to moderately corrosive environment.
Service temperatures: Maximum, dry exposure only: 1°C/248°F.


Finish: Semi-gloss Semi-gloss
Volume solids, %: 42 ± 1 41 ± 1
Theoretical spreading rate: 14.0 m²/litre - 30 micron 13.7 m²/litre - 30 micron
561 sq.ft./gallon - 1.2 mils 548 sq.ft./gallon - 1.2 mils
Flash point: 28°C/82°F 28°C/82°F
Specific gravity: 1.1 kg/litre - 9.2 lbs/gallon 1.1 kg/litre - 9.2 lbs/gallon
Dry to touch: 1 (approx.) hour at °C/68°F 1 (approx.) hour at °C/68°F
V.O.C.: 490 g/litre - 4.1 lbs/gallon 495 g/litre - 4.1 lbs/gallon

Application method: Airless spray Air spray Brush
Thinner (max. vol.): 001(5%) 002 (15%) 003 (5%)
Nozzle orifice: .018"-.021"
Nozzle pressure: 150 bar/20 psi
(Airless spray data are indicative and subject to adjustment)
Cleaning of tools: FY-009
Indicated film thickness, dry: 30 micron/1.2 mils
Indicated film thickness, wet: 75 micron/3 mils
Recoat interval, min: 2 hours (°C/68°F) FY-009
Recoat interval, max: 4 hours (°C/68°F) FY-009
Safety: Handle with care. Before and during use, observe all safety labels on packaging and
paint containers. Avoid inhalation, avoid contact with skin and eyes, and do
not swallow. Take precautions against possible risks of fire or explosions as well as
protection of the environment. Apply only in well ventilated areas.
APPLICATION As dictated by normal good painting practice.
CONDITIONS: In confined spaces provide adequate ventilation during application and drying.
PRECEDING HEMPALIN PRIM 150 or according to specification.

Recoating: Recoating should take place when the first coat is dry and within 4 hours. If this interval is
exceeded, do not recoat until after two weeks. No maximum interval for adhesion.
Before recoating after exposure in contaminated environment, clean surface thoroughly by (high
pressure) fresh water cleaning and allow to dry.
If a skid-proof surface is desired, sprinkle Honestjoy’S Anti-slint 334 evenly over the first coat
of HJ511 while still wet. (Consumption: approximately 7.5 kg 67500 to
litres of paint). When the paint is dry, sweep up surplus grit and apply a second coat of our paint 29
Anti-skid properties can also be attained by mixing 1.0 kg of Honestjoy'S ANTI-SLIP BEADS 674
into litre of HJ511.
Note: It is for professional use only.


Contact Us
Honest Joy Coating & Paint. All rights reserved.