Rapid Dry Gloss Enamel Supplier in China
Rapid Dry Gloss Enamel paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Other coating

Concrete Repair Coatings
Easy Sanding Clear Lacquer Sealer
Hydraulic Fluid Resistant Non-slip Finishes
Highly Reflective Marking Paint

Waterborne Thermosetting Glass Paint
Unsaturated Polyester Glass Flake Putty Coating Paint
Coating for Die Casting Aluminum Galvanize and Steel Parts
Semi-Transparent Organic Solvent Stain
Polyester Epoxy Coil Coating
Hard Abrasive And Weather-Resistant High Gloss Marine Varnish

Alkyd Urea Clear Coat
Concrete Aluminum And Steel Marine Structure Epoxy Coating
Zinc Rich Epoxy Powder Coating

Epoxy Powder Coating
Concrete Aluminum And Steel Marine Structure Epoxy Coating
Water Chemical Resistance Tin Lining Coating
Aqua-Loc Ceramic Topcoat
Removable Petroleum-Based Liquid Barrier Coating
Semi-Gloss Precatalyzed Lacquer
Premium High Build Precatalysed Timber Lacquer
Rapid Dry Gloss Enamel
Temperature Indicating Paint
Two Component Oxirane Ester Paint Containing Active Anti-Corrosive Pigments
Molybdenum Disulfide Slick Lubricant Coating

  

Rapid Dry Gloss Enamel

PRODUCT SPECIFICATIONS:

Features
• Dry to touch in 30 minutes
• Unlimited custom tinted colors
• Interior or exterior use
Recommended For:
• Equipment
• Metal Doors and Cabinets
• Walls and Dadoes
• Machinery
• Tanks and Drums
• Structural Steel
• Metal Roof Decks and Open
Bar Joist
• Catwalks, Railings, and Piping
General Description
This rapid dry gloss enamel is formulated for interior or exterior
use on surfaces requiring a coating that dries to the touch in 30
minutes. Available in unlimited custom tinted colors. This product
permits equipment to be coated while it is being repaired
eliminating additional down time to allow paint to dry.
Limitations:
• Not for immersion service
• Not for application directly on galvanized metal
• Not for floor areas
• Recoat within 3 hours or wait at least 36 hours
• The solvents in this product may lift previously applied
coatings. Test a small area before applying a full coat.
Product Information
Labor Saving Benefits
• The 30 minute dry to touch permits surfaces to be reinstated into service quicker.
• Available in unlimited custom colors satisfying the most stringent color needs.
• This product is formulated for interior or exterior application.
Colors: — Standard: HJ-84 Safety Black


VOC compliant in National AIM and regulated areas

Technical DataTint White
Generic Type Modified Alkyd
Pigment Type Titanium Dioxide
Volume Solids 60%
Theoretical Coverage 480 sq. ft. @ 2.0 Mils
Film Thickness — Wet 3.4 mils
— Dry 2.0 mils
Dry Time @ 70° F — To Touch 30 Minutes
— To Recoat See Limitations
Dries By Oxidation
Dry Heat Resistance 300° F
Viscosity 67 ± 3 KU
Flash Point 92° F
Sheen/Gloss Gloss (80-90 @ 60°)
Surface Temperature
at application – Min. 50° F
– Max. 95° F
Surface must be dry and at least 5° above the dew point.
Reduction — Brush Do not thin
— Roller Do not thin
— Spray Do not thin
Clean Up Thinner HJ-840 or Xylene
Mixing Ratio N/A
Induction Time N/A
Pot Life @ 70° F N/A
Weight Per Gallon 9.5 lbs
Storage Temperature – Min. 40° F
– Max. 90° F
Volatile Organic Compounds (VOC)
335 Grams / Liter 2.79 LBS / Gallon
Surface Preparation
The surface to be painted must be clean, dry and free from oil, grease, dirt,
salts and other contaminants. All loose rust or peeling paint should be
removed and glossy surfaces should be dulled before recoating. If mildew is
evident it must be removed by application of a commercial mildew wash.
CAUTION: Follow manufacturer’s application and safety directions.
WARNING! If you scrape, sand or remove old paint, you may release lead
dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SIOUS
ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSHapproved
respirator to control lead exposure. Carefully clean up with a
vacuum and a wet mop.
Primer/Finish Systems
Ferrous Metal:
Primer: Alkyd Metal Primer (HJ-550)
Finish: 1 or 2 coats Rapid Dry Gloss Enamel (P)
Non-Ferrous Metal: All new non-ferrous metal surfaces must be thoroughly
cleaned with Oil & Grease Emulsifier (HJ-830) to remove
contaminants. New shiny non-ferrous metal surfaces that will be subject to
abrasion should be dulled with very fine sandpaper or a synthetic steel wool pad
to promote adhesion.
Primer: Waterborne Polyamide Epoxy Primer
Finish: 1 or 2 coats Rapid Dry Gloss Enamel (P)
Application
Stir thoroughly before and occasionally during use. Apply one or two coats.
Due to its speed of dry this product is applied most efficiently by spray. Small
areas can be coated with brush or roller.
Spray, Airless: Fluid Pressure —1,500 to 3,000 PSI;
Tip — .011 - .017 Orifice
Thinning/Cleanup
DO NOT THIN
Clean all equipment immediately after use with HJ-840 or Xylene.
USE COMPLETELY OR DISPOSE OF PROPLY. This product contains
organic solvents which may cause adverse effects to the environment if
handled improperly. Disposal of wastes containing either organic solvents or
free-liquids in landfills is prohibited. Dry, empty containers may be recycled in
a can recycling program.
Environmental, Health & Safety
Information.
Contains: Xylene, 2-Heptanone, Ethyl Benzene
HARMFUL OR FATAL IF SWALLOWED. CAUSES IRRITATION TO EYES,
SKIN AND RESPIRATORY TRACT
NOTICE: Repeated or prolonged exposure to organic solvents may lead to
permanent brain and nervous system damage. Intentional misuse by
deliberately concentrating and inhaling vapors may be harmful or fatal.
Keep away from heat and flame. Use only with adequate ventilation. Do not
breathe vapors, spray mist or sanding dust. Avoid contact with eyes and
prolonged or repeated contact with skin. Wear eye protection and gloves. To
avoid breathing vapors or spray mist, open windows and doors or use other
means to ensure fresh air entry during application and drying. If you
experience eye watering, headaches or dizziness, increase fresh air or wear
a properly fitted vapor/particulate NIOSH approved respirator during
application, sanding and clean up. Follow respirator manufacturer’s directions
for respirator use. Close container after each use.
FIRST AID: If affected by inhalation of vapors or spray mist, remove to fresh
air. In case of eye contact, flush immediately with plenty of water for at least
15 minutes and call physician; for skin, wash thoroughly with soap and water.
If swallowed, do not induce vomiting. Get medical attention immediately.
IN CASE OF: FIRE — Use foam CO2, dry chemical or water fog.
SPILL —Absorb with inert material and dispose of as
specified under “Clean Up”.
KEEP OUT OF REACH OF CHILDREN
FOR PROFESSIONAL USE ONLY
Refer to Material Safety Data Sheet for additional health and
safety information.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.