Rapid Drying Primer Supplier in China
Rapid Drying Primer Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Fast Dry Cure,Fast Set Coating

Fast Dry Metal Primer
Rapid Drying Primer
Rapid Drying Copolymer Enamel
Quick Drying One-pack Flexible Primer

Quick Drying Synthetic Primer
Quick Drying Acrylic Primer
Quick Drying Acrylic Lacquer
Polypropylene Air Drying Single Pack Primer
One-component Fast Drying High Build Anti-corrosive Primer
Fast Drying Concrete Floor Paint
Fast Drying Industrial Finishing Enamel

Fast Cure Abrasion Resistant Coating
Fast Dry Fabrication Primer
All Purpose Fast Set Mortar
Fast Curing Enamel



  

Rapid Drying Primer

a rapid drying, adhesion promoting primer for interior and exterior use. It will isolate stains such as nicotine and tannins. It is also ideal for use over difficult substrates including glass, ceramic tiles, melamine, previously painted surfaces and chalky substrates, as well as most wood and non-ferrous metals.
AVAILABILITY
Colour Range White
Packaging 1, 2.5 and 5 litre.
Finish Matt
PROPTIES
Drying Time Under normal drying conditions 1 hour. Allow for adequate ventilation during the
drying period. Allow a minimum of 1-2 hours before recoating.
Composition Pigment: Titanium Dioxide plus inorganic extenders.
Binder: Styrene Acrylic
Solvent: Water.
Spreading Rate 12-14m² per litre on smooth surfaces. On textured surfaces the spreading will be
lower.
Wet Film Thickness 71 micrometres at 14m² per litre.
Dry Film Thickness 23 micrometres at 14m² per litre.
Volume Solids 32%.
Flash Point Not applicable
VOC Content limit value for this product (cat.A/g): 50 g/l (07) / 30 g/l (10) This product
contains max. 2.9 g/l VOC.
Limitations Do not apply when air or substrate temperatures are likely to fall below 8ºC or when
the relative humidity is above 80% during application or the drying period.
PREPARATION
New Surfaces All surfaces must be sound, clean, suitably dry and free from anything that will
interfere with the adhesion of the materials to be applied.
Previously Decorated Surfaces All surfaces must be sound, clean, suitably dry and free from anything that will
interfere with the adhesion of the materials to be applied e.g. dirt, grease etc.
Remove all loose, suspect and failing paint. Feather edges of sound paint.
Remove all dust. Organic growth must be removed and the areas treated with
Honest Fungicidal Solution. Wash smoke, nicotine and graffiti soiled areas
(excluding water stained areas) with hot water and liquid detergent solution to
remove contaminants, frequently changing the water. Any existing multicolour
finishes, glossy or eggshell surfaces should be wet abraded to provide a key. Rinse
with clean water to remove all residues. Allow to dry.
APPLICATION Stir well before use. Apply one or two coats as required by brush or roller.
When used as a stain block primer two coats are recommended.
IfHonest is to be overcoated with a water based finishing system on wood or
metal substrates, a water based Undercoat must also be used.
Note: A trial test area is recommended over severely stained or suspect surfaces.
CLEANING Return surplus material to container. Wash with clean water immediately after use.
HEALTH AND SAFETY Please refer to the Safety, Health and Environmental Information on the container. Take
special precautions during the surface preparation of pre 1960’s painted surfaces as they
may contain harmful lead. m. When preparing all surfaces avoid the inhalation of dust and/or metal
particles. . Store in
secure dry conditions inaccessible to children or animals. Containers should be kept closed
during storage. Do not empty into drains, watercourses or access routes to septic tanks.
GENAL INFORMATION Under normal and frost free conditions this product will remain usable for up to two
years if stored correctly and unopened.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.