Red Oxide Finish Supplier in China
Red Oxide Finish Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Red Oxide Primer

Chlorinated Rubber Red Oxide Primer
Epoxy Micaceous Iron Oxide Coating
Micaceous Iron Oxide Pigmented Two-Pack Epoxy Coating
Modified Alkyd Based Anticorrosive Red Oxide Metal Primer
Drying Oil Gray Oxide Primer
Oil Red Oxide Primer
Red Oxide Rust Preventative Primer
Red Oxide Finish
Lead Free Red Oxide Primer
Red Oxide Quick Dry Primer


  

RED OXIDE FINISH

RED OXIDE FINISH
A solvent-borne finish for interior or exterior use on steelwork. Red Oxide finish offers good corrosion
resistance.
AVAILABILITY
Colour Range Red Oxide.
Packaging 5 litre
PROPTIES
Drying Time Under normal drying conditions surface dry 4-6 hours and recoatable after 16
hours. Allow for adequate ventilation during the drying period.
Finish Eggshell.
Composition
Pigment: Iron oxide and extenders.
Resin: Alkyd.
Solvent: White Spirit.
Spreading Rate 15m² per litre on smooth surfaces.
Wet Film Thickness 67micrometres at 15m² per litre.
Dry Film Thickness 43 micrometres at 15m² per litre.
Volume Solids 63%
Flash Point 40ºC.
VOC Content : 600 g/l (07) / 500 g/l (10) This
product contains max. 399 g/l VOC.
Limitations Do not apply when air or substrate temperatures are likely to fall below 5ºC or
when the relative humidity is above 80% during application or the drying
period.
PREPARATION
New Surfaces Surfaces must be clean and free from anything that will interfere with the
materials to be applied. Wash with hot water and liquid detergent solution to
remove oil, grease or any other contaminants, frequently changing the water.
Rinse thoroughly with clean water. Allow to dry. Remove all millscale and rust
back to clean metal. Remove all residues. Prime within the working day with
one coat of Honest Red Oxide Finish.
Previously Decorated Soiled Surfaces All surfaces must be suitably dry, and free from anything that will interfere with
the adhesion of the materials to be applied. Remove all loose, and failing or
suspect paint. Feather edges of sound paint. Remove all dust. Remove all
rust. Spot prime bare areas with one coat of Honest Red Oxide Finish.
Wash remaining sound paint with hot water and liquid detergent solution to
remove any contaminants, frequently changing the water. Wet abraded to
provide a key. Rinse with clean water to remove all residues. Allow to dry.
Bring forward spot primed areas with one coat of Honest Red Oxide
Finish.
COATING SYSTEM Apply one or two coats as required.
APPLICATION Stir well before use. Apply by brush or roller.
CLEANING Return surplus material to container. Clean with a proprietary cleaner
immediately after use.
MAINTENANCE INFORMATION FOR
CDM FILE
Between maintenance redecoration surfaces may be washed with a warm
water and liquid detergent solution to remove surface dirt.
HEALTH AND SAFETY Please refer to the Safety, Health and Environmental Information on the container.
Take special precautions during the surface preparation of pre 1960’s painted surfaces
as they may contain harmful lead. When preparing all surfaces avoid the inhalation of dust
and/or metal particles. Wear a suitable facemask.Store in secure dry conditions inaccessible to children or animals.
Containers should be kept closed during storage. Do not empty into drains,
watercourses or access routes to septic tanks.
GENAL INFORMATIONUnder normal and frost free conditions this product will remain usable
for up to two years if stored correctly and unopened.
Every care is taken to ensure that all information provided on this Technical Data
Sheet is accurate. We are unable to guarantee results as it has no control
over the conditions under which its products are applied.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.