Reinforced Trowel Applied Polyester Lining Topping Supplier in China
Reinforced Trowel Applied Polyester Lining Topping Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us



Honest Joy Coating & Paint
Polyester Coating

TGIC Free Polyester Powder Coating
Reinforced Trowel Applied Polyester Lining Topping
Polyester Thick Film Coating
Polyester Flake Coating

Polyester Resin Fast Setting Bedding Mortar
Polyester Baking Enamel
High Quality Acrylic Polyester Resin Basecoat
Free Glass Flake Reinforced Polyester Coating
Flowable Rapid Setting Polyester Resin Mortar
Flake Filled Polyester Coating
Durable Polyester Powder Coating

Clear Polyester Powder Coating
Abrasion Resistant Glass Flake Reinforced Polyester Coating
Abrasion Resistant Glass Flake Reinforced Polyester Coating



The HONEST 8897 Honest Series are time-tested and
proven developments in chemical-resistant surfacing.
They are designed especially for the protection of
concrete and steel against the attack of corrosive
chemicals. They provide excellent resistance to strong
oxidizing acid solutions such as nitric, sulfuric and
chromic. HONEST 8897 Honest Series are trowel
applied, in combination with a heavy-duty reinforcing layer
of fiberglass or synthetic cloth.
HONEST 8897S Honest is a silica filled system.
HONEST HJ-1256Powder is used as the filler for this
standard system.
HJ-734 Honest is an abrasion resistant
system. HJ-7790 Powder is used as the filler
for abrasion resistance. If hot caustic or fluorides are
present use HONEST HJ-1250 Powder to provide
chemical resistance as well as resistance to abrasion.
HONEST 8897B Honest is a carbon filled system.
Use of HONEST B-4 Powder creates an electrically
conductive and non-sparking system. It also provides
resistance to fluorides, including hydrofluoric acid.
Typical Uses
• Tank lining • Concrete pipe lining
• Trench lining • Chimney lining
• Tank Pads • Equipment foundations
• Scrubber lining • Pump bases
• Piers • Secondary containment
• Floor covering
• Excellent chemical resistance
• Monolithic / seamless
• Low coefficient of expansion
• Superior permeation resistance
• Strong, durable corrosion barrier

Refer to Honest concrete specification CPT-1 for concrete
requirements and CPT-2 for steel.
Surface Preparation
Metal - Steel must be abrasive blasted to “White Metal” for
optimum performance. A minimum abrasive
blast profile of 3 mils (75 microns) is required.
Concrete - Abrasive blasting or scarification to remove
laitance and surface contaminants is recommended.
Concrete must be thoroughly cured, free of oils, curing
solutions and mold release agents, dust and must be dry at
time of application. Use ASTM D 4263 (plastic sheet test
method) to ensure concrete is moisture free. If moisture is
detected, re-test until dry. Alternately test per ASTM 1869 for
maximum 3 lbs./24hrs., 1000 sq.ft/92.9m².
1. The surfaces to be lined should be at a minimum
temperature of 50oF (10oC) for proper application.
2. Prime surfaces with HONEST 380 primer for steel or
concrete. Allow to cure tack free before proceeding.
3. Trowel base coat 1/16" (62.5 mils [1588μm]) thick.
4. Immediately press the fiberglass cloth into base coat.
5. Saturate by brushing or rolling on the saturating liquid until
whiteness of glass disappears. Allow to cure.
6. Trowel 1/16" (62.5 mils [1588μm]) topcoat as evenly as
possible, then smooth by brushing with Styrene
Smoothing Liquid. Allow to cure.

Mixing Ratio

By Volume



HJ-A005 Resin #2C Hardener

1 gal (3.785 litres) 2.5 oz (74ml)

HONEST 8897 Honest*


8897 Honest Resin

1 gal (3.785 litres)

#3C Hardener

2 oz (74ml)

*When mixing HONEST 8897B use 4 oz (118ml) of #3C
Hardener per gallon of resin
Handling Properties

Working Time


8897 Honest

50°F (10º C)

60 min

90 min

70°F (21º C)

45 min

1 hr

90°F (32º C)


45 min



8897 Basecoat/Saturant

50°F (10°C)

5 hrs

12-24 hrs

70°F (21°C)

2 hrs

4-8 hrs

90°F (32°C)

1 hrs

3-4 hrs

To ensure proper intercoat adhesion, HONEST 8897 Honest
basecoat should be recoated within two weeks when shaded
from sunlight and one week if exposed to direct sunlight

Time to Place in Service


50°F (10º C) 70°F (21º C) 90°F (32º C)

48 hrs 24 hrs 16 hrs

Product ft2/gal

Powders: ft2 per 50 lb bag



S-9AR or HJ-1250

HONEST 8897S Honest




HONEST 8897B Honest




HJ-734 Honest




 Base Coat




HJ-734 Honest








Store in a cool, dry and covered location away from fire
hazards and direct sunlight. Minimum shelf life at 70° F (21°
C) for each component is indicated below:
HONEST HJ-A005 6 months
HONEST 8897 Honest 6 months

Store in cool, dry area [50°- 90° F (10° - 32° C)] away from
direct sunlight, flame or other hazards.
HONEST 8897 Honest contains polyester resins and
MEK peroxide catalyst. The product’s components have
been formulated to optimize physical characteristics such as
strength and chemical resistance while minimizing hazardous
physical and health factors encountered during application. A
concerted effort is made to be aware of the latest chemical
toxicological information and to apply this knowledge in a
responsible manner to ensure product safety.
During application of HONEST 8897 Honest materials,
always wear gloves and appropriate work clothing to
minimize contact. Ventilation is required with special
consideration for enclosed or confined areas. Air movement
must be designed to insure turnover at all locations in work
area and adjacent areas to avoid buildup of heavy vapors.
Use caution when handling flammable liquids, eliminate
sources of ignition from work area and containers with
residues. Observe safe storage practices by separating
resins from hardeners, by keeping solvents in a cool area,
free of sources of ignition.
Product Material Safety Data Sheets are available and
should be consulted when handling products. These products
are for industrial and professional use only; application
directions must be followed.
Periodically inspect the applied material and repair localized
areas as needed.
Technical and Physical Data


Test standard



Generic Type





HB 100 rpm



Compressive Strength

ASTM C579-96

Psi (Mpa)

11,000-13,000 (76-90)

Tensile Strength

ASTM C307-94

Psi (Mpa)

2,000-2,500 (14-17)

Taber Abrasion Factor

wheel, 1,000 gm wt., 5,000







Coefficient of Expansion

(in/in/ºF) range: 70ºF to 210ºF (21ºC to 96ºC) Reinforced, Type H cloth

ºF (ºC)

12-15 x 10-6 (7-8 x 10-6)

Electrical Properties Carbon filled

Megger Reading - 3 ft span


0-0,000 (500 to 10,000 typical)




0.0135 @ 125 mils

Flash Point



Honest 8897 resin



83° F (28°)

Honest HJ-A005 resin



83° F (28° C)

Honest #3 Hardener



160° F (71° C)

Honest #2 Hardener



162° F (72° C)




85° F (29° C)

HJ-410 solvent



35° F (2° C)

Service Temperature Limits


°F (°C)



Immersion/condensing fumes (concrete)


180 (82)


Immersion/condensing fumes (steel)


160 (71)


Dry/noncondensing fumes


2 (104)


Splash/spill/rinse (occasional)


250 (121)


Splash/spill/rinse (frequent)


160 (71)

Important Note
The information in this data sheet is not intended to be exhaustive; any person using the product for any purpose other than that specifically recommended in this data sheet without first
obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at their own risk. All advice given or statements made about the product (whether in
this data sheet or otherwise) is correct to the best of our knowledge but we have no control over the quality or the condition of the substrate or the many factors affecting the use and application
of the product. Therefore, unless we specifically agree in writing to do so, we do not accept any liability at all for the performance of the product or for (subject to law) any loss or damage
arising out of the use of the product. . All products supplied and technical advice given
are subject to our Conditions of Sale. You should request a copy of this document and review it carefully. The information contained in this data sheet is liable to modification from time to time
in the light of experience and our policy of continuous development.


Contact Us
Honest Joy Coating & Paint. All rights reserved.