Self-etching Zinc Chromate Pigmented Vinyl Wash Primer Supplier in China
Self-etching Zinc Chromate Pigmented Vinyl Wash Primer paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Vinyl Coating

Vinyl Fouling Topcoat
Vinyl-Aliphatic Urethane Primer and Finish Coat
Vinyl Wash Primer
Vinyl Red Oxide Primer

Vinyl Intermediate Coating
Vinyl Anti Fouling Topcoat
Vinyl Acrylic Based Exterior Flat Finish
Thin-Film Vinyl Ester Coating
Thick Vinyl Ester Coating
Solvent-thinned Chlorinated Vinyl Toluene-acrylate Low Lustre Coating
Self-etching Zinc Chromate Pigmented Vinyl Wash Primer

Reinforced Trowel Applied Vinyl Ester Lining
Premium Quality Full-bodied Smooth-flowing Vinyl-acrylic Primer
Abrasion Resistant Vinyl Ester Coating
Catalyzed Vinyl Ester Primer
Chlorinated Vinyl Toluene-acrylate Low Lustre Coating

High-hiding Non-bridging Premium Plus Vinyl Flat Finish
Catalyzed Vinyl Ester Primer
Epoxy Vinyl Primer

  

Self-etching Zinc Chromate Pigmented Vinyl Wash Primer

PRODUCT SPECIFICATIONS:

PRODUCT DESCRIPTION
A 2-component self-etching zinc chromate pigmented vinyl wash
primer made especially for difficult to adhere to non-ferrous metals like
aluminum, copper, and unstabilized galvanized steel. Spray applied
in thin coats of 0.1 - 0.3 dry mils, the primer bonds chemically with
the substrate and presents an excellent base for subsequent primers
and topcoats.
FEATURES
• Outstanding adhesion
• Fast drying
• Fast recoat
• Lead free
PRODUCT DATA
Description Results
Vehicle Type ............................. Vinyl Butyral
Colors........................................942 Yellow
Gloss ....................................... 2 - 10 on 60o meter
V.O.C. (mixed)........................... 769 g/l (6.41 lbs/gal)
Weight/Gallon (mixed)............... 7.12 pounds
Solids by Weight (mixed)........... 8.8%
Solids by Volume (mixed).......... 4.6%
Viscosity (mixed)....................... 21" / Zahn 2
Flash Point................................ 41oF
Dry Heat Resistance.................0oF
Freight Classification................. Paint, Flammable
Packaging................................. 1 Gallon
APPLICATION DATA
Description Results
Application................................. Spray
Mix Ratio................................... 1:1
Catalyst..................................... 188
Recommended Thickness......... 0.1 - 0.3 mils DFT
Dry Time @ 77o F, 50% RH
To Touch................................ 5 minutes
To Handle.............................. 5 minutes
To Recoat.............................. 10 minutes
Pot Life...................................... 8 hours
Coverage................................... 148 sf/gal at 0.5 mils DFT
Thinner...................................... Denatured Alcohol up to 5%
Clean Up................................... Denatured Alcohol
EQUIPMENT RECOMMENDATIONS
Listed below are general equipment guidelines for the application of
this product. Job site conditions may require modifications to these
guidelines to achieve the desired results.
SPRAY APPLICATION (General):
AIR ATOMIZED SPRAY:

 

Model

Air Cap

Fluid Tip

Fluid Delivery

Atomizing Pressure

Pressure

63 pb

66

16 oz/min

25 - 60 psi

Pressure

704

fx

16 oz/min

25 - 60 psi

Siphon

66 sf

66

N/A

25 - 60 psi

Siphon

30

fx

N/A

25 - 60 psi

AIRLESS SPRAY:


Model

Pump Ratio

Fluid Tip

Fluid Pressure

Filter Mesh

30:1

.011 - .013

1600 - 00

100

35:1

.011 - .013

1600 - 00

100

GENAL SURFACE PREPARATION
All surfaces must be sound, dry, clean and free of oil, dirt, grease,
wax, mildew, loose or flaking paint and other surface contaminants.
Remove loose, peeling, flaking or scaling paint and rust by scraping,
sanding or wire brush or blasting.
DIRECTIONS FOR USE
TINTING: Do not tint.
THINNING: May be reduced up to 5% with denatured alcohol for
air spray.
APPLICATION: Mix thoroughly before use. Mix 1:1 by volume with
188 catalyst. When applying by spray, see precautions below. Apply
only when air and surface temperatures are between 45-100oF and
the surface temperature is at least 5oF above the dew point. Note:
Topcoat must be applied before exposing primer to weather.
DRYING TIME: Under normal conditions, dries to touch in 5 minutes
and to recoat in 10 minutes. Low temperature, high humidity, poor
ventilation and thick films will retard drying.
CLEAN UP: Clean up skin, clothing, paint tools or spills immediately
with recommended thinner, carefully observing cautions on paint and
thinner labels. Dried paint may be removed by scraping.
HEALTH AND SAFETY
Read the Material Safety Data Sheet (MSDS) and container labels
for detailed health and safety information. This product is intended
for industrial use by properly trained professional applicators only.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.