Single Pack Acrylic Poly Siloxane Finish Coating Supplier in China
Single Pack Acrylic Poly Siloxane Finish Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Acrylic coating

Acrylic Multi-Purpose Primer
Acrylic Eggshell Floor Enamel
Acrylic Clear Coat
Acrylic Enamel For Interior Use

Acrylic Copolymer Exterior Flat Paint
Acrylic DTM Rust Resistant Coatings
Acrylic Elastomer Coating
Acrylic Copolymer Roof Coating
Waterborne Acrylic Enamel Undercoater
Acrylic High Infraed Heat Reflectivity Coating

Acrylic Finish Gloss
Acrylic Conversion Coating
Acrylic Metal Primer

Acrylic Patching Seam Sealer
Acrylic Conversion Coating
Two Pack Catalysed Acrylic Finish
Acrylic Elastomeric Wall Coating
Quick Drying Clear Urethane Alkyd Varnish
Aluminum Acrylic Coating Automotive Grade Acrylic Lacquer Topcoat
Baking Glossy Topcoat Based On Thermoset Acrylic Resin
Rapid Dry Pure Acrylic Coating
Acrylic Urethane Catalyzed Coating
Single Pack Acrylic Poly Siloxane Finish Coating

  

Single Pack Acrylic Poly Siloxane Finish Coating

PRODUCT SPECIFICATIONS:

Composition HJ-1001 is an acrylic polysiloxane high gloss finish coat used with a range of primers and
intermediate coats. HJ-1001 provides a polyurethane-like finish, in one component, without the
isocyanate, as well as better weathering than a standard aliphatic polyurethane. It cures by solventevaporation,
then reaction with atmospheric moisture.
Uses and
Properties
HJ-1001 has been engineered to provide a long lasting, gloss finish for the maintenance and on site
finishing market with the convenience of a single pack product. HJ-1001 has the following properties:
¨ Next generation high gloss finish replacing polyurethane, alkyd enamels and two pack acrylics.
¨ Single component
¨ Isocyanate free
¨ High gloss topcoat and hard, tough surface
¨ Resists soil pick up – easily cleanable
¨ Outstanding weather resistance with excellent colour and gloss retention
¨ Unlimited recoat window
¨ High solids, low VOC
¨ Ease of application, brush, roll and spray
Typical
Applications
As a finish coat over suitably primed steel, concrete or most aged coatings where an attractive
appearance and a wide range of corrosion resistance is required such as Chemical Plants, Pulp and
Paper Mills, Petroleum Refineries, Offshore Platforms, Marine Equipment, Ship Topsides and other
equipment, new building and maintenance projects.
HJ-1001 is compatible with epoxy, alkyds and other types of primers.
It should not be used with Honest coat 221.
Typical
Systems
Substrate Surface Preparation Typical Systems dft mm
Unpainted
Steel
Surface must be free from oil
and grease. Superior life
expectancy is obtained by
abrasive blast cleaning steel to
AS 1627.4 Class 2 ½.
1st Coat: Honest coat 331 �
2nd Coat: Honest coat 11
3rd Coat: HJ-1001
75
150
75
For
Maintenance
of existing
coatings
Prior to coating all surfaces
must be clear, dry,
undamaged and free of all
contaminants, including salt
deposits.
High Pressure Water Clean
existing coatings at pressures
between 3000 psi (.7 MPa)
and 5000 psi (34 MPa)

Corroded areas must be
power cleaned to
AS 1627.2
1st Coat: Honest 101
2nd Coat: HJ-1001
125
75
HJ-1001 may be applied directly to most existing coatings other than
polyester urethanes.
General Data
Weathering Excellent.
Finish High gloss.


Chemical Resistance

Environment

Splash & Spillage

Fumes and Weathering

Acidic

No

Yes

Alkaline

Yes

Yes

Petroleum products

Yes

Yes

Solvents

No

No

Salt Solutions

Yes

Yes

Water

Yes

Yes

Abrasion Resistance Very Good.
Immersion Not recommended.
Temperature Range Continuous 93°C, intermittent 121°C.
Colour Full colour range.
Shelf Life 12 months if stored in sealed containers away from heat or moisture.
Application Data
Theoretical Coverage 7.3 sq.m. per litre at 75 mm dry film thickness. (Wet film thickness 140 μm). Material
losses during mixing and application will vary and must be considered when estimating
requirements.
Volume Solids 55% ± 3% (theoretical).


Drying Time

Temperature

10°C

21°C

32°C

Touch

3 hrs

2 hrs

1 hr

Through

24 hrs

12 hrs

8 hrs

Recoat

min

8 hrs

4 hrs

2 hrs

 

 

max

unlimited

unlimited

unlimited

NOTE: The figures quoted for drying and curing times are not definitive. They are
dependent on site conditions, such as ambient and steel temperatures, weather and
ventilation.
Mixing Open with caution as pressure may have built up in container. Stir thoroughly before use,
to produce a uniform product. Replace lid on unused material.
Thinners Use Thinner-041 for spray application up to 5% V/V. For cleanup use HJ-043.
Application method:
Separate regulators for air and fluid pressure, mechanical pot agitator and moisture oil
trap in the main air supply line are recommended. Can be applied by brush, roll or spray.
Safety Precautions HJ-1001 contains flammable solvents. Keep away from sparks and naked flames. When
applying by brush or roller, provide adequate ventilation. When applying by spray, users
must comply with relevant spray painting regulations and wear appropriate respirator to
avoid inhaling vapours and spray mist. Material Safety Data Sheet is available and
should be consulted.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.