Solvent Based Anti-slip Floor Paint Supplier in China
Solvent Based Anti-slip Floor Paint Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Industry protect coating

Ultra-high Build Single-component Coal Tar Mastic
Ultimate Chemical Resistant Coating
Two-pack High Solids High Performance Maintenance Coating
Two-component Chemical Resistant Enamel

Surface Tolerant Self-priming Corrosion Inhibitor Coating
Structrial Steel Primer
Sovent Borne Alkali Resisting Primer
Solvent-borne Aluminium Finish
Solvent Based Anti-slip Floor Paint
Single Component Penetrating Corrsion Inhibitor
Single Component Industrial Maintenance Primer

Multifunctional Chemical Resistant Coating
Moisture Resistant Lacquer
Pipe Coating
Anti Static Coating
Anti-Static Conductive Primer




  

Solvent Based Anti-slip Floor Paint

PRODUCT SPECIFICATIONS:

A solvent-borne high performance coating for interior use over coated or uncoated concrete, stone, metal and
wood floor surfaces. Resistant to abrasion, scuffing, spillages of oils, petrol, detergents and dilute aqueous
chemical solutions.
AVAILABILITY

Packaging 5 litre
PROPTIES
Drying Time Under normal drying conditions surface dry in 3-4 hours recoatable after 16 hours. Allow for
adequate ventilation during the drying period. Recoat within 48 hours.
Finish Eggshell
Composition
Pigment: Titanium Dioxide, coloured pigments and extenders.
Resin: Epoxy ester.
Solvent: White Spirit.
Spreading Rate 15m² per litre depending on surface texture.
Wet Film Thickness 67 micrometres at 15m² per litre.
Dry Film Thickness 21 micrometres at 15m² per litre.
Volume Solids 32% Red other colours will vary.
Flash Point 40oC (closed cup).
VOC Content limit value for this product (cat.A/i): 600 g/l (07) / 500 g/l (10) This product contains
max. 499 g/l VOC.
Limitations For interior use only. Do not apply when air or substrate temperatures are likely to fall below
5ºC or when the relative humidity is above 80% during application or the drying period.
PREPARATION
New Surfaces All surfaces must be sound, clean, suitably dry and free from anything that will interfere with
the adhesion of the materials to be applied. Remove any site debris and sweep floor clean.
Any oil or grease from site plant/works must be removed with an emulsifying de-greaser in
accordance with the manufacturer's instructions. Floor areas to be coated should be acid
etched to remove surface laitance, using a proprietary mortar cleaner diluted in accordance
with the manufacturer's instructions. Rinse thoroughly with clean water to remove all
residues. Allow to dry. Prime all areas to be coated with one coat of Anti-Slip Floor Paint.
Previously Decorated Surfaces All surfaces must be clean, dry and free from anything that will interfere with the adhesion of
the materials to be applied. Remove loose and failing material by scraping or brushing with a
stiff bristle brush to a sound edge. Any oil, grease, polish etc must be removed with an
emulsifying de-greaser in accordance with the manufacturer's instructions. For surface dirt,
wash with hot water and liquid detergent solution to remove any contaminants, frequently
changing the water. Rinse thoroughly with clean water to remove all residues. Allow to dry.
Feather edges of sound coatings and mechanically dry abrade any glossy surfaces to provide
a key. Remove all dust by vacuum cleaning. Patch prime all bare areas (including any areas
of making good) with one coat of Anti-Slip Floor Paint,
thinned up to 5% by volume with clean dearomatised white spirit. Bring forward with one coat
of Anti-Slip Floor Paint within 48 hours of drying.
COATING SYSTEM Apply two coats as required.
APPLICATION Apply two coats as required. Maintain a wet edge. The second coat must be applied within 48
hours.
CLEANING Return surplus material to container. Clean with a proprietary cleaner immediately after use.
MAINTENANCE INFORMATION
FOR CDM FILE
Between maintenance redecoration surfaces may be washed with a warm water and liquid
detergent solution to remove surface dirt.
HEALTH AND SAFETY Please refer to the Safety, Health and Environmental Information on the container. Take
special precautions during the surface preparation of pre 1960’s painted surfaces as they
may contain harmful lead. When preparing all surfaces avoid the inhalation of dust and/or metal
particles. . Store in
secure dry conditions inaccessible to children or animals. Containers should be kept closed
during storage. Do not empty into drains, watercourses or access routes to septic tanks.
GENAL INFORMATION Under normal and frost free conditions this product will remain usable for up to two
years if stored correctly and unopened.
Every care is taken to ensure that all information provided on this Technical Data Sheet is
accurate. Honest joy is unable to guarantee results as it has no control over the conditions
under which its products are applied.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.