keypro Supplier in China
keypro Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us



Honest Joy Coating & Paint
Industry protect coating

Ultra-high Build Single-component Coal Tar Mastic
Ultimate Chemical Resistant Coating
Two-pack High Solids High Performance Maintenance Coating
Two-component Chemical Resistant Enamel

Surface Tolerant Self-priming Corrosion Inhibitor Coating
Structrial Steel Primer
Sovent Borne Alkali Resisting Primer
Solvent-borne Aluminium Finish
Solvent Based Anti-slip Floor Paint
Single Component Penetrating Corrsion Inhibitor
Single Component Industrial Maintenance Primer

Multifunctional Chemical Resistant Coating
Moisture Resistant Lacquer
Pipe Coating
Anti Static Coating
Anti-Static Conductive Primer




A solvent-borne finish for interior or exterior use on metals. Aluminium paint produces a durable bright finish
with high heat and light reflectance. Heat resistant up to 232ºC. May be used over Zinc
Phosphate or Primer when surface temperature does not exceed 60ºC.
Colour Range Aluminium.
Packaging 1 and 5 litre
Drying Time Under normal drying conditions surface dry 4-6 hours and recoatable after 16 hours.
Allow for adequate ventilation during the drying period.
Finish Metallic lustre.
Pigment: Aluminium paste.
Resin: Hydrocarbon.
Solvent: White Spirit.
Spreading Rate 14m² per litre on smooth surfaces.
Wet Film Thickness 71 micrometres at 14m² per litre.
Dry Film Thickness 36 micrometres at14m² per litre.
Volume Solids 50%
Flash Point 40ºC (closed cup).
VOC Content limit value for this product (cat.A/i): 600 g/l (07) / 500 g/l (10) This product
contains max. 487 g/l VOC.
Limitations Do not apply when air or substrate temperatures are likely to fall below 5ºC or when
the relative humidity is above 80% during application or the drying period.
New Surfaces All surfaces must be clean and free from anything that will interfere with the materials
to be applied. Wash with hot water and liquid detergent solution to remove oil, grease
or any other contaminants, frequently changing the water. Rinse thoroughly with clean
water. Allow to dry. Remove all millscale and rust back to clean metal. Remove all
residues. Prime within the working day with one coat of Aluminium Paint.
Previously Decorated Surfaces All surfaces must be suitably dry, and free from anything that will interfere with the
adhesion of the materials to be applied. Remove all loose, and failing or suspect
paint. Feather edges of sound paint. Remove all dust. Remove all rust. Spot prime
bare areas with one coat of Aluminium Paint. Wash remaining sound
paint with hot water and liquid detergent solution to remove any contaminants,
frequently changing the water. Wet abraded to provide a key. Rinse with clean water
to remove all residues. Allow to dry. Bring forward spot primed areas with one coat of
Aluminium Paint.
COATING SYSTEM Apply one or two coats as required.
APPLICATION Stir well before use. Apply by brush or roller.
CLEANING Return surplus material to container. Clean with a proprietary cleaner immediately
after use.
HEALTH AND SAFETY Please refer to the Safety, Health and Environmental Information on the container.
Take special precautions during the surface preparation of pre 1960’s painted surfaces
as they may contain harmful When preparing all surfaces avoid the inhalation of dust
and/or metal particles. Wear a suitable facemask. Store in secure dry conditions inaccessible to children or animals.
Containers should be kept closed during storage. Do not empty into drains,
watercourses or access routes to septic tanks.
Under normal and frost free conditions this product will remain usable
for up to two years if stored correctly and unopened.
Every care is taken to ensure that all information provided on this Technical Data
Sheet is accurate. Honest joy is unable to guarantee results as it has no control
over the conditions under which its products are applied.


Contact Us
Honest Joy Coating & Paint. All rights reserved.