Superior Solvent Chemical and Elevated Temperature Resistance Phenolic Coating Supplier in China
Superior Solvent Chemical and Elevated Temperature Resistance Phenolic Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Phenol coating

VOC Compliant Phenolic Coating
Marine Spar Varnish
Rust Inhibitive Phenolic Modified Alkyd Primer
Phenolic Primer

Pigmented Short Phenolic Modified Alkyd Primer
Phenolic Two Component Epoxy Coating
Phenolic Modified Primer
Phenolic Heavy Duty Gym Floor Finish
Phenolic Alkyd Metal Primer
Two-Component Amine Adduct Crued Phenolic Epoxy Paint

Superior Solvent Chemical and Elevated Temperature Resistance Phenolic Coating
Quick Drying Phenolic Modified Alkyd Based Primers
Epoxy Phenolic Topcoat

Reinforced Hybrid Epoxy Phenolic Lining
Quick Drying Phenolic Modified Alkyd Based Primers
Two-Component Amine Adduct Crued Phenolic Epoxy Paint
Moisture Tolerant Lining
Baking Cross-Linked Epoxy-Phenolic Coating
Air Dry Phenolic Coatings

  

Superior Solvent Chemical and Elevated Temperature Resistance Phenolic Coating

PRODUCT SPECIFICATIONS:

DESCRIPTION HJ-513is a high solids fast curing technologically advanced hybrid epoxy phenolic novolac
designed to provide superior solvent, chemical, and elevated temperature resistance.
TYPICAL USE Designed for use as an interior lining for storage tanks, process tanks, and pipelines in the petroleum and
chemical process industries.
BENEFITS - One or two coat application - User friendly
- Resists wide range of chemicals - Does not require bake
- High solids and low VOC - Excellent adhesion
LIMITATIONS OF USE Consult your representative.
TECHNICAL DATA Weight (lbs/gal): 12.83 VOC (mixed lbs/gal): 1.61
Volume Solids: 76% VOC (mixed g/l): 193
Pot Life (@75° F): 2 hours Recommended Thickness:
Color(s): Tan, Red Two coat system- 5-6 mils dry, 6-8 mils wet per coat
Flash Point: 40° F One coat system- 10-12 mils dry, 12-16 mils wet
Hardness (ASTM D3363 min.): 5H Maximum system dry film thickness is 15 mils
Temperature Resistance:
Non-Immersion, Dry Heat: 300° F (149° C)
Continuous immersion temperature resistance is dependent on particular reagent exposure.
COVAGE Theoretical Coverage*: 1219 sq. ft per gallon @ 1 mil dry
@ 6 mils: 3 sq. ft. per gallon
@ 12 mils: 102 sq. ft. per gallon
*When ordering product, make allowances for any loss due to overspray, surface irregularities, etc.
(approx. 15 – %).
MINIMUM DRY TIME 77º F and 50% relative humidity, ASTM D 1640:
To Touch: 5 hours
To Handle: 17 hours
To Recoat: overnight
Maximum Recoat Time: 2 days @ 77º F
CURE SCHEDULE Ventilation: Adequate ventilation is required during application and curing process.
For Immersion Service: 3 days with ventilation at 77° F or higher and 50% relative humidity. ASTM
D3363 Pencil Hardness of 5H is recommended.
Post Cure Applications: After application of final coat, provide forced air ventilation for a minimum of one
hour. Slowly increase steel temperature at a rate of 30°F per hour. When steel temperature reaches 150°F
discontinue heat and maintain ambient air temperature ventilation a minimum of one hour.
SURFACE PREPARATION All surfaces must be clean, dry, and free of dust, dirt, oil or other foreign matter. Steel surface shall be
abrasive blasted to a minimum SSPC SP-10/Nace No. 2 Near White Metal finish with a minimum 2½ mil
profile for best results. Concrete shall be abrasive brush blasted or etched with 10% muriatic acid. Use of a
primer is required for concrete to improve adhesion and minimize outgassing.
APPLICATION EQUIPMENT Spray is preferred for appearance and film build control.
MIX RATIO 2:1 by volume.
APPLICATION CONDITIONS Apply at 5° F (3° C) above dew point. Use the following chart for preferred temperature and humidity
conditions. These conditions plus adequate ventilation must be maintained throughout the curing cycle.


Substrate        Ambient       Humidity

Preferred

55-1° F

55-1° F

N/A

Minimum

55° F

55° F

5° above dew point

HANDLING Store at moderate temperatures (65-85º F) prior to application for ease of handling and mixing.
THINNING Thinning is not recommended for maximum performance at elevated temperature immersion service.
Thinning also reduces hanging qualities of the lining and will slow cure.
PRE-HEATING Not required for HJ-340.
MIXING Mechanically pre-mix each component one minute; then mix combined compound with mechanical mixer at
400-600 rpm until homogeneous. Allow a 15 minute induction time. Remix before application.
CLEAN UP Clean immediately with methyl ethyl ketone (MEK) or methyl isobutyl ketone (MIBK).
PACKAGING One unit forms approximately 4 gallons consisting of two components:
Resin: 5 Gallon Pail Hardener: 2 Gallon Pail
SHELF LIFE 2 years when stored at 75° F (24° C) unopened.

SAFETY This product is for industrial use only and should be installed by qualified coating and lining specialists.
Consult Material Safety Data Sheets for important health and safety information prior to use.
Important Note
The information in this data sheet is not intended to be exhaustive; any person using the product for any purpose other than that specifically recommended in this data sheet without first
obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at their own risk. All advice given or statements made about the product
(whether in this data sheet or otherwise) is correct to the best of our knowledge but we have no control over the quality or the condition of the substrate or the many factors affecting the
use and application of the product.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.