Surface Tolerant Self-priming Corrosion Inhibitor Coating Supplier in China
Surface Tolerant Self-priming Corrosion Inhibitor Coating Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Industry protect coating

Ultra-high Build Single-component Coal Tar Mastic
Ultimate Chemical Resistant Coating
Two-pack High Solids High Performance Maintenance Coating
Two-component Chemical Resistant Enamel

Surface Tolerant Self-priming Corrosion Inhibitor Coating
Structrial Steel Primer
Sovent Borne Alkali Resisting Primer
Solvent-borne Aluminium Finish
Solvent Based Anti-slip Floor Paint
Single Component Penetrating Corrsion Inhibitor
Single Component Industrial Maintenance Primer

Multifunctional Chemical Resistant Coating
Moisture Resistant Lacquer
Pipe Coating
Anti Static Coating
Anti-Static Conductive Primer




  

Surface Tolerant Self-priming Corrosion Inhibitor Coating

PRODUCT SPECIFICATIONS:

Description
HJ-8480 is Aluminum Finish, single component, surface tolerant self-priming corrosion inhibitor coating for
use on suitably prepared steel substrates.
Generic Type
Single-component RMCI (Reactive Metal Corrosion Inhibitor) compound in a fast drying modified silicone alkyd
resin with excellent gloss and color retention properties.
Recommended Uses
A fast drying aluminium finish surface tolerant corrosion inhibiting coating that can be used on substrates not subject
to severe abrasion. Especially suited for maintenance coating in Infrastructure, Marine, or General Industrial
applications. Also suitable for:
• Steel Bridge Structures • Transmission Towers
• Marine & Offshore above waterline • Pipelines / Storage Tanks
• Structural Steel / Rebar • Suspension Cables
Physical Properties

Volume Solids

56%

Tack-Free Time

5 Hours at 240C (750F)

Specific Gravity

1.03 kg/L (8.62 lb/Gal)

Color & Finish

Aluminum satin finish

Recommended Minimum DFT

125-300 micron (5-12 mils)

Viscosity

100-1 K.U.

Theoretical Coverage @ 125mm (5 mils)

4.5 m2/L (182 sq.ft./Gal)

V.O.C.

444 g/L (3.7 lb/Gal)

Preparation / Application Procedures
All surfaces to be coated must be cleaned using 5,000 psi high-pressure water cleaning with a zero degree rotating
tip .All cleaned areas should then
be blown out with clean dry high-pressure air (100 PSI) to insure moisture has been removed.
Product Application
Thoroughly wet out all connections, crevices, cables, back-to-back angles, tube interiors and areas to be protected
with HJ-0180 and allow minimum 4 hours before applying HJ-8480.
HJ-8480 should not be applied at temperatures below 180C (650F) and with a steel temperature not less
then 180C (650F).
Application over previously coated surfaces will require 125-150mm (5-6 mils) DFT, and on abrasive blasted or new
steel substrates, required DFT will be 250-300mm (10-12 mils). Note: For specific application procedures, please
consult your Coatings representative or distributor and DO NOT commence product application before
referring to specific HJ-8480 Product Application Procedures Sheet.
Precautions
Treat as flammable liquid - Flashpoint 400C (1040F). Keep away from heat, open flame and sparks. Avoid contact
with skin and eyes. Avoid prolonged breathing of vapor. Read label instructions carefully and refer to Material
Safety Data Sheet supplied. This product is for industrial use only and is not intended for use in or around a
household or dwelling.
Warranty
The Manufacturer warrants the product to be free from defects in material and workmanship. The seller’s sole obligation and
Buyer’s exclusive remedy in connection with the products shall be limited, at the seller’s option, to either replacement of products
not conforming to this warranty or credit to Buyer’s account in the invoiced amount of the nonconforming products.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.