Two-Component State-OF-The-Art Silicone Coating Supplier in China
Two-Component State-OF-The-Art Silicone Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Fire proof retardant heat resistance coating

VOC Compliant Air Drying Silicone Based Heat Resistant Coating
Two-Component State-OF-The-Art Silicone Coating
Fouling Release Tiecoat

Single Component High Heat Aluminum Coating
High Heat Resistant Black Coating
Silicone Based Heat Resistant Coating
Quick Drying Heat Resistant Aluminium Enamel
Aluminium Heat Resistant Pure Silicone
Air Drying Self-Priming Heat And Corrosion Coating

Compliant VOC High Build Modified Silicone Coating
Solventborne Silicone Coating
Heat Reflective Ceramic Coating

General Purpose Aqueous Based Fire Retardant Surface Coating
Solventborne Silicone Coating
Air Drying Self-Priming Heat And Corrosion Coating
One-Coat Aluminum Fire Resistance Coating
Coloured Heat Resistant Acrylic Silicone
Fire Retardant Coating

  

Two-Component State-OF-The-Art Silicone Coating

PRODUCT SPECIFICATIONS:

General Properties
A two-component, state-of-the-art silicone coating that can be subjected to temperatures up to 4oC (790oF) without
the need for a heat cure. This fast-drying product has a low sheen finish with good anti-corrosive properties.
Recommended Uses
This product is for use on steel surfaces where excellent heat resisting performance is required.
Product Information

Methods of Application
AIRLESS SPRAY
CONVENTIONAL
BRUSH / ROLL Brushing and rolling is limited to small areas or touch-up
Drying Time - Temperature, Relative Humidity, and Film Thickness will affect dry and re-coat times.
Substrate
Temperature
oC (68oF)
Touch Dry
15 minutes
Hard Dry
1 hour
Minimum
1 hour
Overcoat Interval
Maximum
24 hours
Normal
8 hour
Recommended Primer
STEEL
WEATH GOOD
13-Nov-07
Some package sizes or colors may be by special order only.
ACIDS
STORAGE
PACKAGE SIZE

CONCRETE
Not recommended
GALVANIZED
Not recommended
ALUMINUM
Not recommended
Surface Preparation
Surfaces to be coated must be clean, dry and free from grease, oil or other contaminants. All mill scale or
weld spatter must be removed for maximum performance. The minimum surface preparation required is
SSPC-SP10 Near White Blast Cleaning but an SSPC-SP5 White Metal Blast Cleaning is recommended for
improved product performance. Surface profile should not exceed 1.25 mils as this is a thin film coating.
Typical Resistance (Non-immersion)

Limitations
Do not apply where surface temperatures will exceed recommended temperature resistance levels. Not for immersion
service. When HJ-7895 is used as a base coat and top coated with HJ-7145, total dry film thickness of the two coat system shall not exceed 2 mils dry.
Mixing Instructions
Mix HJ-908 Series A with good agitation. Add B component zinc dust to HJ-908 Series A, stirring constantly. Never add
liquid component to zinc dust. Continue mixing until a smooth consistency is attained. If necessary, strain through a
30 to 60 mesh screen to remove any lumps before using. Mix frequently during use as required.
Safety Precautions
This product is for industrial use only. Refer to Material Safety Data Sheet for proper health and safety information.
Storage and Handling
FLASH POINT
24oC (75oF) TCC
PRODUCT WEIGHT
15.4 lbs/gal (container extra)
STORAGE
Cool, dry, well ventilated area.
PACKAGE SIZE
1 gallon kit, 5 gallon kit
Some package sizes or colors may be by special order only. Please check with us when ordering.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.