Two-component Zinc Rich Epoxy Primer Supplier in China
Two-component Zinc Rich Epoxy Primer Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Zinc primer.htm

Zinc-rich Ethyl Silicate Based Coating
Zinc Silicone Primer Heat Resistant to 500F
Zinc Rich Epoxy Primer
Zinc Rich Epoxy Cold Galvanising Coating

Zinc Phosphate Primer
Zinc Phosphate High Build Anticorrosive Primer-Finish
Zinc Ethyl Silicate Primer
Zinc Chromate metal Primer
Weldable Modified Zinc Ethyl Silicate Pre-fabrication Primer
Two-component Zinc Rich Epoxy Primer
Surface Tolerant Reinforced Inorganic Zinc Primer

Solvent-borne Self-curing Inorganic Zinc Silicate Primer
Reinforced Inorganic Zinc Primer
Chlorinated Rubber Zinc Rich Coating

Epoxy Zinc Phosphate Iron Oxide Primer
Epoxy Polyamide Anticorrosive High Performance Primer

Fast Drying Low VOC Zinc Rich Epoxy Primer

Inorganic Hybrid Zinc Rich Protective High Temperature Primer
Quick Dry High Performance Zinc Phosphate Primer
Free Low VOC Rreinforced Inorganic Zinc Primer
Solvent-borne Self-curing Inorganic Zinc Silicate Coating



  

PRODUCT SPECIFICATIONS:

PRODUCT DESCRIPTION
A high performance, two component zinc rich primer for use
where corrosion resistance is paramount. Provides cathodic
protection through sacrificial electro-chemical reaction of the
zinc pigment. For use on steel structures, trucks, trailers, railway
cars, bulk tanks or chemical (acid or caustic) trailers.
For best results, use the Honest joy engineered system
for a total coating system.
FEATURES
• Excellent adhesion
• Solvent resistant
• Excellent corrosion resistance
• Same catalyst as HJ-88
• Low VOC
PRODUCT DATA
Description Results
Vehicle Type...................................... Epoxy Urethane
Color.................................................. Gray
Gloss................................................. Low Gloss
VOC (mixed)..................................... <240 g/L (<2.0 lbs/gal)
Weight/Gallon (mixed)....................... 22.1 pounds
Solids by Weight (mixed)................... 90.3%
Solids by Volume (mixed).................. 69.8% (Theoretical)
Viscosity (mixed)............................... 1,500 cps
Flash Point (white)............................ 98oF
Dry Heat Resistance......................... 300oF (149oC)
Freight Classification......................... See MSDS
Packaging......................................... 1.5 Gallon Units
APPLICATION DATA
Description Results
Application......................................... Spray
Mix Ratio........................................... 3:1 by Volume
Catalyst............................................. HS-110 or HS-111
Recommended Thickness................. 3.0 mils DFT
Dry Time @ 77oF, 50% RH
No Accelerator Spray
Recoat....................................... 2 hours
Tack Free.................................. 3 hours
Handle....................................... 6 hours
With .5 fl oz/gal 99041
Recoat....................................... 1 hour
Tack Free.................................. 2 hours
Handle....................................... 4 hours
Pot Life @75oF, 50% RH
No Accelerator
2X Viscosity............................... 1.5 hours
Gell Time................................... 8 hours
With .5 fl oz/gal 99041
2X Viscosity............................... 1 hours
Gell Time................................... 4 hours
Coverage........................................... 373 sf/gal at 3.0 mils DFT
Thinner
Medium Reducer........................... HJ-092 up to 15%
Retarder........................................ 21093 up to 3%
Fast Reducer................................. 21102
Clean Up........................................... HJ-092
The technical specifications for this data sheet are based on
product Gray.
CURED FILM PFORMANCE
Description Test Method Results
Adhesion to Steel ASTM D4541 >500 psi
Hardness ASTM D3363 2H
Corrosion Resistance ASTM B117 3,000 Hours
EQUIPMENT RECOMMENDATIONS
Listed below are general equipment guidelines for the application
of this product. Job site conditions may require modifications
to these guidelines to achieve the desired results.
SPRAY APPLICATION (General): The following spray equipment
has been found suitable and is available from manufacturers

AIR ATOMIZED SPRAY:

 

Model

Air Cap

Fluid Tip

Fluid Delivery

Atomizing Pressure

Pressure

63 pb

66

oz/min

45 - 60 psi

Pressure

704

fx

oz/min

45 - 60 psi

AIRLESS SPRAY:


Model

Pump Ratio

Fluid Tip

Fluid Pressure

Filter Mesh

30:1

.015 - .021

1800 - 20

100

35:1

.015 - .021

1800 - 20

100

GENAL SURFACE PREPARATION
For best results, an SSPC-SP 10 (NACE No. 2) near-white
blast is minimum for severe exposure. For moderately severe
(non-immersion) exposures an SSPC-SP 6 (NACE No. 3) commercial
blast can be used.
DIRECTIONS FOR USE
TINTING: Do not tint.

Note: Always know local VOC restrictions for coating applications
in your area before thinning this product. Thinning recommendations
meet VOC restrictions for architectural
coatings. This product and other referenced products may
not meet VOC restrictions for your application and may not be
available in your area. Carefully read and observe warning
on thinner labels.
APPLICATION: Mix thoroughly before use. Add 1 quart of HS-110
or HS-111 per ¾ gallon unit of then mix thoroughly again.
Only apply when air and surface temperature are between
40o – 100oF (7o - 38oC) and when the surface temperature is at
least 5 degrees (F) or 3 degrees (C) above the dew point. Use
of agitator pot or pail is strongly recommended.
DRYING TIME: See Application Data for typical dry times. Low
temperature, high humidity, poor ventilation and thick films will
retard drying. HJ1104 may be added at the rate of
up to 0.5 fl oz per mixed gallon of HS2 to reduce
the drying time.
CLEAN UP: Clean up paint tools or spills immediately with
recommended thinner, carefully observing cautions on paint
and thinner labels. Dried paint may be removed by scraping.
ENGINEED SYSTEM
For maximum corrosion resistance and durability. Recommended
for use in coastal and marine exposures above the
splash zone over a sandblasted surface.
First coat Primer: 3 dry mils of HS2 Organic
Zinc Rich Primer.
Second intermediate coat: 3-5 dry mils of (white) or
(gray) ..
Topcoat: 3 dry mils of HJ-88 in the desired
color for the finish coat.
Clearcoat: 1 dry mil of HJ-88 Clear (optional
for ultimate gloss and durability).
HEALTH AND SAFETY
Read the Material Safety Data Sheet (MSDS) and container
labels for detailed health and safety information. This product
is intended for industrial use by properly trained professional
applicators only.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.