Urethane Alkyd Based Toopcoat Supplier in China
Urethane Alkyd Based Toopcoat paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Alkyd coating

Urethane-Modified Alkyd Primer
Urethane Alkyd Enamel
Urethane Alkyd Based Toopcoat
Epoxy Ester Modified Alkyd Primer

Superior Quality Alkyd Glaze
Speedy-Dry Alkyd Enamel
Silicone Modified Alkyd Enamel
Semi-Transparent Organic Solvent Stain
Rust-Inhibitive Patented Acrylic Modified Alkyd Enamel
Quick-Drying Styrenated Alkyd Paint

Alkyd Urea Clear Coat
Transparent Modified Alkyd Sealer
Alkyd Semigloss Finish
Transparent Modified Alkyd Sealer
Quick Drying Modified Alkyd Based Primer
Rust Preventing Primer
Quick Drying Clear Urethane Alkyd Varnish
Versatile Finish Coat Based On Long Oil Alkyd Resin Exceptionally Durable Fast Drying Alkyd Paint
Fast Dry Alkyd Metal Primer
Alkyd Gloss Enamel
High Gloss Alkyd Aluminum Paint
Alkyd Baking Enamel

  

Urethane Alkyd Based Toopcoat

PRODUCT SPECIFICATIONS:

Product description
Mammut Topcoat is a high build urethane alkyd based topcoat. This product is part of a complete system which is
certified not to spread surface flames.
Recommended use
As topcoat over Mammut Primer or other alkyd based primers on steel structures for general marine and industrial
purposes, exterior and interior.
Film thickness and spreading rate
Minimum Maximum Typical
Film thickness, dry (μm) 50 100 80
Film thickness, wet (μm) 100 0 160
Theoretical spreading rate (m²/l) 10 5 6,3
Physical properties
Colour Grey 38, White, White BT
Solids (vol %)* 50 ± 2
Flash point 36ºC ± 2
VOC 400 gms/ltr .
Gloss Glossy
Gloss retention Good
Water resistance Fair
Abrasion resistance Good
Flexibility Good

Surface preparation
Coated surfaces
Clean, dry and undamaged compatible primer.
Other surfaces
The coating may be used on other substrates.
Condition during application
The temperature of the substrate should be minimum 3ºC above the dew point of the air, temperature and relative
humidity measured in the vicinity of the substrate. Good ventilation is usually required in confined areas to ensure
correct drying.
Application methods
Spray Use airless spray
Brush Recommended for stripe coating and small areas, care must be taken to achieve the specified dry
film thickness.
Roller May be used. However when using roller application care must be taken to apply sufficient material
in order to achieve the specified dry film thickness.
Application data
Mixing ratio (volume) Single pack.
Thinner/Cleaner Honest joy Thinner No. 2
Guiding data airless spray
Pressure at nozzle 15 MPa (150 kp/cm², 2100 psi)
Nozzle tip 0.46 - 0.69 mm (0.018 - 0.027")
Spray angle 65-80°
Filter Check to ensure that filters are clean.
Drying time
Drying times are generally related to air circulation, temperature, film thickness and number of coats, and will be
affected correspondingly. The figures given in the table are typical with:
* Good ventilation (Outdoor exposure or free circulation of air)
* Typical film thickness
* One coat on top of inert substrate
Substrate temperature 5°C 10°C 23°C 40°C
Surface dry 3 h 2 h 1 h 0,5 h
Through dry h 9 h 4 h 2 h
Dry to recoat, minimum 36 h 12 h 8 h 5 h
Dry to recoat, maximum 1
1. The surface should be dry and free from any contamination prior to application of the subsequent coat.
The given data must be considered as guidelines only. The actual drying time/times before recoating may be shorter or
longer, depending on film thickness, ventilation, humidity, underlying paint system, requirement for early handling and
mechanical strength etc. A complete system can be described on a system sheet, where all parameters and special
conditions could be included.
Typical paint system
Mammut Primer 1 x 80 μm (Dry Film Thickness)
Mammut Topcoat 1 x 80 μm (Dry Film Thickness)
Other systems may be specified, depending on area of use
Storage
The product must be stored in accordance with national regulations. Storage conditions are to keep the containers in a
dry, cool, well ventilated space and away from source of heat and ignition. Containers must be kept tightly closed.
Handling
Handle with care. Stir well before use.
Packing size
litre container

Health and safety
Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do not
breathe or inhale mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable cleanser,
soap and water. Eyes should be well flushed with water and medical attention sought immediately.
For detailed information on the health and safety hazards and precautions for use of this product, we refer to
the Material Safety Data Sheet.
DISCLAIM
The information in this data sheet is given to the best of our knowledge based on laboratory testing and practical
experience. However, as the product is often used under conditions beyond our control, we cannot guarantee anything
but the quality of the product itself. We reserve the right to change the given data without notic

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.