Urethane-Modified Alkyd Primer Supplier in China
Urethane-Modified Alkyd Primer paint coating manufacture Shenzhen China  
Home About Us Products Contact Us



Honest Joy Coating & Paint
Alkyd coating

Urethane-Modified Alkyd Primer
Urethane Alkyd Enamel
Urethane Alkyd Based Toopcoat
Epoxy Ester Modified Alkyd Primer

Superior Quality Alkyd Glaze
Speedy-Dry Alkyd Enamel
Silicone Modified Alkyd Enamel
Semi-Transparent Organic Solvent Stain
Rust-Inhibitive Patented Acrylic Modified Alkyd Enamel
Quick-Drying Styrenated Alkyd Paint

Alkyd Urea Clear Coat
Transparent Modified Alkyd Sealer
Alkyd Semigloss Finish
Transparent Modified Alkyd Sealer
Quick Drying Modified Alkyd Based Primer
Rust Preventing Primer
Quick Drying Clear Urethane Alkyd Varnish
Versatile Finish Coat Based On Long Oil Alkyd Resin Exceptionally Durable Fast Drying Alkyd Paint
Fast Dry Alkyd Metal Primer
Alkyd Gloss Enamel
High Gloss Alkyd Aluminum Paint
Alkyd Baking Enamel


Urethane-Modified Alkyd Primer


Description: Feiyang-139 is a quick-drying, urethane-modified alkyd primer.
Recommended use: General purpose primer for protection of steel in mild to medium
atmospheric corrosive environments.
Service temperatures: Maximum, dry exposure only: 1°C/248°F.


Finish: Flat
Volume solids, %: 44 ± 1
Theoretical spreading rate: 5.9 m²/litre - 75 micron
235 sq.ft./gallon - 3.0 mils
Flash point: 38°C/100°F
Specific gravity: 1.2 kg/litre - 10.0 lbs/gallon
Surface dry: 1 (approx.) hr at °C/68°F
Dry to touch: 4 (approx.) hours at °C/68°F
V.O.C.: 455 g/litre - 3.8 lbs/gallon

Application method: Airless spray Brush (touch up)
Thinner (max.vol.): 08080 (5%) 08080 (5%)
Nozzle orifice: .021"-.023"
Nozzle pressure: 0 bar/2900 psi
(Airless spray data are indicative and subject to adjustment)
Cleaning of tools: FY-009
Indicated film thickness, dry: 75 micron/3 mils
Indicated film thickness, wet: 175 micron/7 mils

Safety: Handle with care. Before and during use, observe all safety labels on packaging and
paint containers. Avoid inhalation, avoid contact with skin and eyes, and do
not swallow. Take precautions against possible risks of fire or explosions as well as
protection of the environment. Apply only in well ventilated areas.
SURFACE New steel: Abrasive blasting to Sa 2½ is recommended. For temporary protection, if required,
PREPARATION: use a suitable zinc-free or low-zinc shopprimer. All damage of shopprimer and contamination from
storage and fabrication should be thoroughly cleaned prior to final painting. For repair and touch-up
Maintenance: Remove oil and grease, etc. with suitable detergent. Remove salt and other
contaminants by (high pressure) fresh water cleaning. Remove all rust and loose material by
abrasive blasting or power tool cleaning. Dust off residues. Touch up to full film thickness.
APPLICATION As dictated by normal good painting practice.
CONDITIONS: In confined spaces provide adequate ventilation during application and drying.

REMARKS: Some of the certificates have been issued under the former quality number 13.
Film thicknesses: May be specified in another film thickness than indicated depending on purpose and area of use.
This will alter spreading rate and may influence drying time and recoating interval. Normal range
dry is 50-75 micron/2-3 mils.
Recoating: Recoating intervals related to later conditions of exposure:
(75 micron/3 mils dry film thickness of Feiyang-139)




Surface temperature






Recoated with





HEMPALIN, except 53240 and 130 130 53240

5 hours 5 hours 5 days

8 hours 8 hours 5 days

None None None

3 days None 10 days

If the maximum recoating interval is exceeded, roughening of the surface is necessary to ensure
intercoat adhesion.
Before recoating after exposure in contaminated environment, clean the surface thoroughly with
(high pressure) fresh water and allow drying.


Contact Us
Honest Joy Coating & Paint. All rights reserved.