Versatile Finish Coat Based On Long Oil Alkyd Resin Supplier in China
Versatile Finish Coat Based On Long Oil Alkyd Resin paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Alkyd coating

Urethane-Modified Alkyd Primer
Urethane Alkyd Enamel
Urethane Alkyd Based Toopcoat
Epoxy Ester Modified Alkyd Primer

Superior Quality Alkyd Glaze
Speedy-Dry Alkyd Enamel
Silicone Modified Alkyd Enamel
Semi-Transparent Organic Solvent Stain
Rust-Inhibitive Patented Acrylic Modified Alkyd Enamel
Quick-Drying Styrenated Alkyd Paint

Alkyd Urea Clear Coat
Transparent Modified Alkyd Sealer
Alkyd Semigloss Finish
Transparent Modified Alkyd Sealer
Quick Drying Modified Alkyd Based Primer
Rust Preventing Primer
Quick Drying Clear Urethane Alkyd Varnish
Versatile Finish Coat Based On Long Oil Alkyd Resin Exceptionally Durable Fast Drying Alkyd Paint
Fast Dry Alkyd Metal Primer
Alkyd Gloss Enamel
High Gloss Alkyd Aluminum Paint
Alkyd Baking Enamel

  

Versatile Finish Coat Based On Long Oil Alkyd Resin

PRODUCT SPECIFICATIONS:

Product Description
HJ-0611 is a versatile finish coat based on long oil alkyd
resin.
Recommended Use
As a finish coat on exterior and interior of steel
structures, wood substrates and massonaries, previously
primed with alkyd primers.
Outstanding Characteristics
- Good gloss and colour retention
- Excellent sprayability
- Excellent flexibility
- Good resistance in mildly to moderate corrosive
environments
Surface Preparation
The surface must be clean, dry and free from any
contamination such as grease, salt and loose paint.
Old primed surfaces should be roughened before
repainting.

Technical Data Finish

Semi gloss / gloss

Colour

 Upon request

Volume Solids

40 ± 2%

Specific Gravity

1.01 ± 0.1 gr/cm3

Flash Point

38 °C

Recommended D.F.T.

40 - 60 microns

Theoretical coverage

10-6.6 sqm/lit 9.9-6.6 sqm/kg

Practical Coverage

Depends on loss factor

Touch dry

5 hrs at °C

Hard dry

7 days at °C

Thermal Resistance

 1 °C

Shelf life

12 months at 25 °C

Package

liter container

Application Details

 

Application method

Air/Airless spray, Brush, Roller

Nozzle orifice Nozzle pressure

.019"-.021" 150 bar / 20 Psi

Application temperature

10 - 50 °C

Mixing ratio

single pack

Thinner/Cleaner

HJ-0311

Pot life

N/A

Recoat interval

Min 24 hrs Max indefinite

Application Procedure HJ-0611
1. Flush all equipment with recommended cleaner before use.
2. Stir the product thoroughly with a power mixer.
3. For conventional spray, thin with no more than 15% of
recommended thinner for workability. For airless spray 5% of
thinner is normally sufficient.
4. Apply a wet coat by parallel passes. Overlap each pass 50%
to avoid bare areas, pinholes or holidays.
5. Double coat all welds, rough spots, sharp edges, rivets,
bolts, etc. to ensure proper thickness.
6. Check thickness of dry coating with a non-destructive dry
film thickness gauge. Recoat if greater thickness is required.
Note: If the maximum recoating interval is exceeded,
roughening of the surface is necessary to ensure intercoat
adhesion.
Before recoating after exposure in contaminated environment,
clean the surface thoroughly by (high pressure) fresh water
hosing and allow to dry.
7. Random pinholes, holidays and small damaged or bare areas
can be touched up by brush when the film is dry to touch.
Larger areas should be resprayed.
8. In confined areas ventilate with clean air during application
and drying until all solvents are removed.
9. Clean all equipment with recommended cleaner immediately
after use.
Limitations
Surface temperature must be at least 3°C above dew point.
Relative humidity during application should be less than 80%.
Do not apply coatings under reverse environmental conditions.
Safety
This product is flammable. Keep away from heat
and open flame. Keep container closed. Avoid
prolonged and repeated contact with skin.
Since improper use and handling can be hazardous
to health and cause fire or explosion, safety
precautions included with application instructions
must be observed during all storage, handling, use
and drying periods.
If used in confined areas:
- circulate adequate fresh air continuously during
application and drying.
- Use fresh air masks and explosion proof
equipment
- Prohibit all flames, sparks, welding and smoking
- Take precautionary measures against static
discharges
Keep away from food products.
Storage and Handling
The products must be stored in accordance with
national regulations.
The products should be kept in a cool and well
ventilated place protected from heat and direct
sunlight. Containers must be kept tightly closed.
Handle with care. Stir well before use.
Remarks
The information in this data sheet is given to the
best of our knowledge based on laboratory testing
and practical experience.
However we reserve the right to change the given
data without notice.
Any recommendation relating to the use of the
products, is based on data believed to be reliable. It
is buyer to satisfy itself of the suitability of the
product for its own particular use .
As the product is often used under conditions
beyond our control, we cannot guarantee anything
but the quality of the product itself.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.