Vinyl Acrylic Based Exterior Flat Finish Supplier in China
Vinyl Acrylic Based Exterior Flat Finish paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Vinyl Coating

Vinyl Fouling Topcoat
Vinyl-Aliphatic Urethane Primer and Finish Coat
Vinyl Wash Primer
Vinyl Red Oxide Primer

Vinyl Intermediate Coating
Vinyl Anti Fouling Topcoat
Vinyl Acrylic Based Exterior Flat Finish
Thin-Film Vinyl Ester Coating
Thick Vinyl Ester Coating
Solvent-thinned Chlorinated Vinyl Toluene-acrylate Low Lustre Coating
Self-etching Zinc Chromate Pigmented Vinyl Wash Primer

Reinforced Trowel Applied Vinyl Ester Lining
Premium Quality Full-bodied Smooth-flowing Vinyl-acrylic Primer
Abrasion Resistant Vinyl Ester Coating
Catalyzed Vinyl Ester Primer
Chlorinated Vinyl Toluene-acrylate Low Lustre Coating

High-hiding Non-bridging Premium Plus Vinyl Flat Finish
Catalyzed Vinyl Ester Primer
Epoxy Vinyl Primer

  

Vinyl Acrylic Based Exterior Flat Finish

PRODUCT SPECIFICATIONS:

DESCRIPTION: HJ Exterior Flat is a vinyl acrylic based exterior flat finish for new and previously painted
masonry. HJ Exterior Flat is durable, applies easily, and has good hide. Its flat finish allows for excellent touchup.
SPECIFICATIONS
SOLVENT TYPE RESIN TYPE
Waterborne Vinyl acrylic
FINISH
Flat. 1-2% on a 60° meter.
COLORS
Stock colors: White. Other colors can be special ordered from
the factory.
VISCOSITY AT 77°F (25°C)
118-123 Ku
VOC CONTENT
55 g/L (as supplied)
SOLIDS BY VOLUME SOLIDS BY WEIGHT
39.5.0% 53.0%
WEIGHT P GALLON
12.45 lbs.
COMPOSITION BY WEIGHT
Pigment - 41.0% Vehicle - 59.0%
*Prime pigments ............ 9.0 Vinyl acrylic resins...............10.5
Reinforcing pigments ... 32.0 Water & additives................48.5
* Prime pigments include titanium dioxide (TiO2), plus all other
pigments directly adding to the hiding power of this paint.
RECOMMENDED FILM THICKNESS P COAT
Wet: 3.8 mils Dry: 1.5 mils
PRACTICAL COVAGE P COAT AT RECOMMENDED
DRY FILM THICKNESS
75-0 sq. ft. per gallon, depending on surface conditions.
AVAGE DRY TIME AT 77°F (25°C)
To touch: 2 hours
Recoat: 4 hours
APPLICATION EQUIPMENT
Brush, roller, airless spray. Commonly used airless spray tip:
.517
PACKAGING
Five-gallon containers
MATIAL SAFETY DATA SHEET
Form #1
SURFACE PREPARATION
All surfaces must be cured, clean, dry, and free from dirt, dust,
rust, stains, grease, oil, mildew, wax, efflorescence and other
contaminants. Remove all loose, peeling, or chalky paint by
sanding, scraping, high-pressure washing or other appropriate
methods. Repair all cracks, holes, and other surface
imperfections with a suitable patching material. Repaired
surfaces should match the surrounding surface texture. If
efflorescence exists, remove all noticeable deposits and prime
the entire surface with HJ252 - Waterborne
Epoxy Primer or HJ253 - Acrylic Masonry Sealer.
SPECIAL INSTRUCTIONS
· If the air or surface temperature is between 37°F and 50°F,
add HJ254 - Cold Weather Reducer per label
directions.
· Do not apply when the air or surface temperature is below 37°F.
THINNING RECOMMENDATIONS
HJ-781 should be thinned with one to one and a half gallons of
water per five gallons of paint.
CLEANUP
Water

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.