Vinyl Fouling Topcoat Supplier in China
Vinyl Fouling Topcoat Coating paint coating manufacture Shenzhen China  
Home About Us Products Contact Us

 

 




Honest Joy Coating & Paint
Vinyl Coating

Vinyl Fouling Topcoat
Vinyl-Aliphatic Urethane Primer and Finish Coat
Vinyl Wash Primer
Vinyl Red Oxide Primer

Vinyl Intermediate Coating
Vinyl Anti Fouling Topcoat
Vinyl Acrylic Based Exterior Flat Finish
Thin-Film Vinyl Ester Coating
Thick Vinyl Ester Coating
Solvent-thinned Chlorinated Vvinyl Toluene-acrylate Low Lustre Coating
Self-etching Zinc Chromate Pigmented Vinyl Wash Primer

Reinforced Trowel Applied Vinyl Ester Lining
Premium Quality Full-bodied Smooth-flowing Vinyl-acrylic Primer
Abrasion Resistant Vinyl Ester Coating
Catalyzed Vinyl Ester Primer
Chlorinated Vinyl Toluene-acrylate Low Lustre Coating

High-hiding Non-bridging Premium Plus Vinyl Flat Finish
Catalyzed Vinyl Ester Primer
Epoxy Vinyl Primer



  

Vinyl Fouling Topcoat

PRODUCT SPECIFICATIONS:

HJ-0912 is a phisically drying anti-fouling topcoat based
on a vinyl copolymer resin with a high toxicity level.
Recommended Use
as a anti-fouling topcoat for vinyl system on exterior of
immersed marine steel structures and ships.
Outstanding Characteristics
- High toxicity providing excellent anti- fouling property
- Excellent water resistance
- Excellent durability
Surface Preparation
The surface must be clean, dry and free from any
contamination such as grease, rust, mill scale, salt and
loose paint. Old painted surfaces must be cleaned with
high pressure water guns.

Technical Data

 

Finish

 Flat

Colour

Red

Volume Solids

52± 2%

Specific Gravity

1.6 ± 0.1 gr/cm3

Flash Point

30 °C

Recommended D.F.T.

30 - 50microns

Theoretical coverage

17.3 – 10.4 sqm/lit 10.8 – 6.5 sqm/kg

Touch dry

30min at °C

Hard dry

3 hrs at 35 °C

Shelf life

12 months

Package

4 & liter containe

Application Details

 

Application method

Air/Airless spray, Brush, Roller

Application temperature

10 - 40 °C

Mixing ratio

single pack

Thinner/Cleaner

FX-80

Pot life

N/A

Recoat interval

Min 8 hrs Max 2 months

Application Procedure HJ-0912
1. Flush all equipment with recommended cleaner
before use.
2. Stir the product thoroughly with a power mixer.
3. For conventional spray, thin with no more than
10-15% of recommended thinner for workability.
For airless spray 5% of thinner is normally
sufficient.
4. Apply a wet coat by parallel passes. Overlap each
pass 50% to avoid bare areas, pinholes or holidays.
5. Spray with standard airless spray equipment
having a 28:1 or higher pump ratio and a tip with a
0.48-0.53 mm orifice, or with conventional spray
with a 2.2-2.8 mm orifice to obtain an even wet coat
with minimum overspray.
6. Double coat all welds, rough spots, sharp edges,
rivets, bolts, etc. to ensure proper thickness.
7. Check thickness of dry coating with a nondestructive
dry film thickness gauge. Recoat if
greater thickness is required.
8. Random pinholes, holidays and small damaged or
bare areas can be touched up by brush when the film
is dry to touch. Larger areas should be resprayed.
9. In confined areas ventilate with clean air during
application and drying until all solvents are
removed.
10. Clean all equipment with recommended cleaner
immediately after use.
Limitations
Surface temperature must be at least 3°c above dew
point.
Relative humidity during application should be less
than 80%.
Do not apply coatings under reverse environmental
conditions.
Safety
This product is flammable. Keep away from heat
and open flame. Keep container closed. Avoid
prolonged and repeated contact with skin.
Since improper use and handling can be hazardous
to health and cause fire or explosion, safety
precautions included with application instructions
must be observed during all storage, handling, use
and drying periods.
If used in confined areas:
- circulate adequate fresh air continuously during
application and drying.
- Use fresh air masks and explosion proof
equipment
- Prohibit all flames, sparks, welding and smoking
- Take precautionary measures against static
discharges
Keep away from food products.
Storage and Handling
The products must be stored in accordance with
national regulations.
The products should be kept in a cool and well
ventilated place protected from heat and direct
sunlight. Containers must be kept tightly closed.
Handle with care. Stir well before use.
Remarks
The informations in this data sheet is given to the
best of our knowledge based on laboratory testing
and practical experience.
However we reserve the right to change the given
data without notice.
Any recommendation relating to the use of the
products, is based on data believed to be reliable. It
is buyer to satisfy itself of the suitability of the
product for its own particular use .
As the product is often used under conditions
beyond our control, we cannot guarantee anything
but the quality of the product itself.

 



Contact Us
 
Honest Joy Coating & Paint. All rights reserved.